n00b advice needed, building system tomorrow

DubiousDoc

n00b
Joined
Jul 29, 2004
Messages
27
I ordered a barebones system consisting of:

Tsunami 3000 Case
MSI Neo2 Plat Mobo
AMD64 3500 (90nm)
1 gig Corsair TwinX
Antec Truepower 550

I am going to reuse my 9800XT vid card
I am adding a new WD Raptor 74 gig HD
Audigy 2z Soundcard
reusing DVD and CD burner for now

I would appreciate ANY and ALL tips, hints, and caveats you could throw my way regarding setting up my new system; Equipment you would recommend; utilities; order of installation; etc.

Thanks.
 
READ the manuals and learn how to use google

The back end of AGP cards tend not to go in all the way...even though the rest of the card did.

Don't use too much pressure or overtighten.
 
Some little points that probably won't make a difference, but you never know:

1.) Put in the ram before the vid card, because a lot of times, the ram retention mechanism won't open all the way because its too close to the vid card if it's in.
2.) Remember thermal paste, and to be sure that your heatsink is making good contact. (Don't ask ;) )
3.) Don't put the soundcard in the PCI slot right below the vid card. They usually share resources and so it can cause sound card crackle.
4.) Don't put too many high load components on a single power lead. Divide up the components to each set of connectors on the power supply to avoid overloading the PSU.
And most importantly-
5.) NEVER BE AFRAID TO ASK. The guys here are usually pretty good about helping people out with problems, and it's free. Not asking and fucking up your hardware is expensive. Remember- everyone was a n00b at some point. ;)
 
first and foremost ground yourself!!! :p you probably know this, but just in case. The first thing you should do is seat the processor in the motherboard, place the paste on the cpu, and then fit the heatsink & fan. It is natural to want to start putting things in the case but doing this first makes sense. If you try and do this when the mobo is in the case you can slip a screwdriver and destroy bus lines, capacitor, etc. once this is done I always cover my PSU cables. Next you may want to decide which power leads you will actually use and tie up/ hide the rest. Also before you put the mobo in try to see if you can hide any more wires behind it. well I'll let everyone else chip in to but there's a start. good luck on your build :cool:
 
There are some very smart folks on these forums. Any honest question usually always gets an honest reply, in a very reasonable time frame. Never, ever, be shy about saying "I don't know" or "I'm not sure". We all destroyed expensive hardware, er, learned a lot over the years.....:D From now on, when someone asks "...where did you get that PC?" you get to say "...built it myself."

Everyone may do this in a slightly different order, but what I do is (Reader's Digest Condensed Book Version):

- Open the case. Get it on the bench and open it up. Get to the place where the MoBo will mount; be it a removable tray or the bottom of the case.
- Get the MoBo on the bench, on the static bag.
- Make sure the mounting holes in the mobo match the standoffs in the case / tray.
- Install the CPU.
- Install the HSF.
- Install the RAM.
- Mount the Mobo in the case. Take the mobo back out, and swear at me for not reminding you about making sure the ATX EMI gasket was installed.
- Mount the drives.
- Wire the power to the MoBo.
- Wire the power to the drives.
- Wire the power to the video card, if required.
- Wire the data cables to the drives. Realize how nice those reasonably priced round IDE cables would be, for the optical drives you have....
- Wire the case front panel switches to the MoBo
- Offer a short prayer to the gods of the orderly electron.

...go for the boot test....:eek:

If possible, burn one of these ahead of time:

http://www.ultimatebootcd.com/

And.....learn a bunch and have fun.....:cool:

Regards - B.B.S.
 
Thanks for the advice, I'll let you know how I made out. I have gleaned a great deal of knowledge form these pages and I will not hesitate to raise the whiteflag when I am over my head.
 
Fezdog192 said:
Some little points that probably won't make a difference, but you never know:

1.) Put in the ram before the vid card, because a lot of times, the ram retention mechanism won't open all the way because its too close to the vid card if it's in.

HAHAHA make sure you do this, my like 100th time inside my computer I did it the wrong order and nocked a resistor off my videocard
:eek:
 
Back
Top