My first oc, hows everything look?

Joined
Dec 13, 2004
Messages
820
This is my first attempt at oc'ing. The specs are:

Asus A8N-SLI mobo
AMD 3500+ Winchester core with XP-120 and some slow fan
Patriot DDR PC3200 ram with xbl (2X512)
misc other stuff

So my maxs were determined by using an Athlon guide I found posted here:

Max FSB/HTT 315mhz
Max CPU 2630mhz at 1.55V (board wont go any higher on vcore)
Max memory 272mhz at 3-4-4-8 (2T)

So I set the following in BIOS:

HTT/FSB 260mhz
HT link X3
CPU Multiplier X10
RAM 200mhz (1:1) giving me 260mhz at 2.5-3-3-7 (I was able to tighten the timings slightly) at 2T.

It all seems stable so far, am I missing anything? Temps are good, SuperPi finished with no errors.

Anything elese I need to do?
 
have you run orthos for 8 hours? because superpi and orthos are 2 different things
 
Orthos is for C2D isn't it? Looks good to me

edit: gee vcore is max... i'd lower it a little. like 1.525. or is it unstable then?

I know you can get a little higher, your ram is holding you back. I used patriot ram on one of my clients computers and based on my overclocking with them...not so good. G.skill would be a better overclocker
 
I will run Orthos now. I will also drop the vcore slightly and see if it's stable.

Incidently, I would never have done this if it weren't for this place!
 
AuroraProject said:
I will run Orthos now. I will also drop the vcore slightly and see if it's stable.

Incidently, I would never have done this if it weren't for this place!


Yep... Now you have the disease... There's no cure. Overclocking is like herpes, buying hardware soothes the virus, but you can never truely cure it.

PS: ew?
 
Ok, vcore is at 1.525v and it appears stable. Idle temp is 44, load is 52-55 but I have Q-Fan on. I'll need to disable that and probably get a better fan for the xp-120.

Edit: I also have the ram at 2.7V, is that too much? It seems to be doing fine.
 
Scratch that, it only made it 10 minutes into Orthos and errored out. I bumped the vcore to 1.575 and am trying again.
 
O_O don't fry your chip man ;)
if it really is your ram holding you back, just try out a divider. from what i remember, A64s don't get much of a performance hit from running a divider.
 
omz said:
O_O don't fry your chip man ;)
if it really is your ram holding you back, just try out a divider. from what i remember, A64s don't get much of a performance hit from running a divider.


eh, it'll just give me an excuse to upgrade! I kid.

Maybe I'll just be happy with 2.5ghz.
 
Ok, I give up. I can't even get 2.5ghz with 1.4v stable. Every combination I've tried will error out in Orthos either right away, or within 15-20 minutes. I don't know what I'm doing wrong here.
 
The Winchester core is more or less your problem. There are very few of them that have gone over the 2.5Ghz mark on an air OC. You can pick up a cheap Venice core out of the FS/FT forum on site here and it will OC better than what you have now (even the 3000+).

Try a divider on the ram or loosen the timings. The PDP Patriot PC3200+XBLK that I had didn't fair very well at high frequencies but that was on a DFI Ultra-D also.

I have a 3500+ Venice core and I got just a smidge over 1.6vcore to it on a Neo2 Platinum. I have it OC'd to 2.8Ghz and it runs cool even tho I am on air. Core temp is telling me 27C idle right now and I never seen it crack 45c loaded.
 
Back
Top