MSI K8N Neo2 Problem

dayamdave

Limp Gawd
Joined
Jan 24, 2005
Messages
288
Is it just me, or whenever I do anything with my mobo, like rewire cables, rearrange my drives or just anything that involves disconnecting cables, this board just doesn't want to turn on when im done. It was like this when I bought the board, at first I thought i had the wrong power sw connection but after fiddling with it for a day it would turn on. great, everything should be fine from here. but noooo, whenever i fiddle with the computer, it doesn't want to turn on, on occasion i will get a sign of life in it where it turns on for 2 seconds all fans on then shuts off. anyone else experiencing this problem? should i rma this or am i doing something wrong? i never experienced this problem with any other mobo i have had.

p.s.- i always ground myself before i touch anything in there.

specs -
msi k8n neo2 & 3000+ winnie
ocz platinum el rev2 pc3200 2x512
bfg 6800gt oc
400w psu
 
I would pull it all out of the case and set it up on a piece of cardboard. Then basically plug it all in and run it out of the case To eliminate the possibillity of a short somewhere. You have in your sig a 400W PSU but whats the brand? Make sure the Cpu fan is plugged in> make sure all ram is in the correct slots 1&2 correctly and tight. Make sure PSU connection to mobo are tight and the 4Pin 12V plug is also good and plugged in.
 
I have the Neo2 Platinum (specs in sig) and when using a Antec 400W PSU, i would get the cold boot problem. I would have to turn off the PSU power via the switch to get the machine back up and running. I would try a difference PSU first. Make sure you do have the mobo mounts on the mobo tray and its not touching anywhere.
 
Yeah, right now im just using some generic psu I've had for 3 years, never had a problem. Eventually I will upgrade, but this was the only mobo I had this problem with. The mobo isn't touching anything but the screws that came with the chieftec dragon case. Whenever I do anything that involves unplugging a cable or two, it gives me a hard time turning on. I shut off the psu for a few minutes, plug it in. nothing. on occasion i get about 2 seconds of life then it goes dead again. i tried reseting cmos to see if that was a prob and sometimes..it'll work, other times no. so i got sick of it and left the house for awhile. came back later that night and my computer was on.....iono if its just me or did i get a really buggy mobo. when it works, it works like a charm....when it doesnt, man i just wanna melt this thing.
 
I have the same setup as you:
Neo2, Winnie 3000+, OCZ Plat 2(1Gb), BFG 6800 GT OC.

except I have a 425W Enermax Noisetaker PSU.

I have changed components and wires around and have never had that problem. Sounds like a bad PSU to me.

Hope that helps.....
 
I Would agree that it sounds like a PSU problem to me. It pretty well known that the 939 platform and especially this board dont care to much for generic PSU. Not enough amps normally and the true watts are never as they advertise. I would recomend a good name brand like Pc pwr and cooling, Zippy, OCZ or Antec. and it never hurts to ge as big as possible. 500w and atleast 30 amps on the 12v+ line.
 
I also run the same mb. There are some strange issues with the new winnie processors sometimes... They do seem to be kinda picky about powersupplies, and certain memory modules. So I would agree with these guys.
 
1.41b, i haven't changed anything on the comp yet because its so buggy. its up and running now, and overclocked fairly nicely. 2475mhz running ddr550 all stable. ill be sure to pick up a new psu, definately. thanx for the help!
 
Back
Top