MSI K8N Neo2 Plat - HELP!

GaleForce

Gawd
Joined
Aug 7, 2004
Messages
761
I just built my computer, but I'm running into a bit of a problem. I have a WD Raptor 10k RPM SATA drive. There are two SATA connections on the mobo, should I use the upper or lower one? Also, I have two optical drives, a DVD-ROM and a DVD RW, obviously IDE. Should I plug that into the white port or the blue port on the mobo?

The reason I ask is the system posts and everything but up on the screen it says "Media test failure. Check cables."

Quick assistance would be most appreciated. Thanks!
 
If i was being harsh i would say RTFM, but im not ;)

The blue IDE slot is IDE1, white is 2. There are actually 4 SATA headers on the board, 2 under the IDE slots and 2 over on the other side of the board. I believe you can run off any of the headers. Dont forget to turn on DMA for SATA in the bios else you will get slow performance out of them.

EDIT : to boot off the SATA drive, you'll probably need to install the drivers that came on the floppy - hit f6 while the disk is in the drive.
 
I know blue is IDE1, but I don't know which one I should plug the optical drives into.

Also, what should the jumpers be for everything? If you could tell me 1st column, 2nd, etc that would be great, although I can RTFM to get that. I just need to know if the optical drives should both be slaves, or CS, and what the SATA drive should be.

I'll let you know after that if I still get the failure message.
 
1) The PC doesn't have a floppy drive.

2) I'm not trying to boot off of the SATA, I want to boot from a Windows CD-ROM.

3) Its an OEM drive. :D
 
As you dont have any other drives you can either run one on one IDE channel and the other optical drive on the other or set them up as master or slave - it doesnt matter to windows. Just make sure the jumpers are set for master/slave if you do it that way.

You shouldnt need to alter any jumpers on the board. Id imagine whats happening is that the bios isnt seeing your SATA drive to try and boot off - have you set the bios to boot off that? I dont have an SATA drive so i cant help much more than that. Have you installed the drivers for SATA from the floppy?
 
GaleForce said:
1) The PC doesn't have a floppy drive.

2) I'm not trying to boot off of the SATA, I want to boot from a Windows CD-ROM.

3) Its an OEM drive. :D

set the boot sequence to CDrom first and that should boot off that. Does the bios see your optical drives? If not, double check any jumpers on the drives. How are you planning to install windows if you dont have SATA drivers installed? Im not sure if there is native support for them or not.
 
I don't have a floppy drive and I don't have a floppy driver disk. When you say make sure I set the master/slave, should both opticals be slave? or should one be master?

Windows is NOT installed yet. I need to install it, but it won't let me because I'm getting that error message.
 
GaleForce said:
I don't have a floppy drive and I don't have a floppy driver disk. When you say make sure I set the master/slave, should both opticals be slave? or should one be master?

Windows is NOT installed yet. I need to install it, but it won't let me because I'm getting that error message.

If they are both on the same IDE cable, one needs to be master, the other slave. If you have 2 IDE cables you can set both to master and use both IDE channels.
 
Ya both were slave. I put the slave one on cable select even though I guess in retrospect i didnt need to, and when I tried to put my master in CS I bent a pin so I just stuck it on master. Windows setup is starting up now. Thanks for your help :).

BTW, where is that SATA Bios setting you were talking about for performance?
 
Goto intergrated peripherals, IDE function setup and down towards the bottom theres SATA1/2 DMA transfer and SATA3/4 DMA transfer - set those to enable.

Glad you are up and running!
 
Thanks! Windows is formatting right now. Hopefully next time I post it will be from my new PC :D.
 
GaleForce said:
Thanks! Windows is formatting right now. Hopefully next time I post it will be from my new PC :D.


good luck, I love this motherboard.
 
Back
Top