MSI board bios prob

Grimdj

Limp Gawd
Joined
Nov 12, 2004
Messages
240
Hey peoples!

Might have been tackled before, but I can't locate it....

Here's the problem: Just built my new box, here are the specs:

AMD 3500+ A64
MSI Neo2 Platinum
Hitachi SATA HDD
Plextor 712A
512mb pc2700 in slot 1

Everything went in fine, but when I power it up, I can't go into BIOS. I'm fairly sure everything is hooked up correctly. HDD in SATA port 1. DVD drive set to master. I fire it up, and I get to the screen that says "Platinum", and at the bottom says press<TAB> to POST, and press <DEL> to enter BIOS. I get nothing from either.
I've tried 3 different keybords, and I can CONTROL ALT DELETE with them, so I know they are at least being recognized. I'm stumped. Might be overlooking something simple...any suggestions?

Thanks in advance!
 
sorry-forgot to mention

PNY 6800gt
Soundblaster Audigy 2
Thermaltake Butterfly 480w psu
 
Well you asked for simple so here goes, I kinda have the same problem, by the time the damned boot splash screen goes away I am halfway into windows. Here are a couple of simple things.

Instead of restarting do a cold boot from power off and tap the del key every couple of seconds startting from the instant you power on the system. also try tab then del count to 1 try tab and del again etc. as it powers up.

I think with msi if you hold down the insert key as you do a cold boot it resets the bios to factroy defaults and will come up in the bios or at least do the extended memory test and give you time to hit the tab and then the del key, Check you manual.

Clear the bios with the jumper. Typically it will boot to the bios then.


On my problem machne I have to leave extended boot on while I tweak stuff and only when happy do I set it to fast boot/post. Ahh for the old days when I could go get a cup of coffe and not spill a drop waiting for "True Blue" to post. Best of luck. You just have to catch it at the right moment.
 
are these keyboards USB or PS/2? Do the lights light up on the keyboard at all on boot? do you have the diagnostic LED's hooked up? do they show any errors? Will the board get past the platinum screen and try to POST?

have you tried clearing the CMOS?


****EDIT***

didn't see the part where you said you can ctrl-alt-del on the keyboards.. probably is just as simple at timing.. new boards now a days boot so quick, you almost have to be holding down the key, before it even mentions hitting that key, for it to work..

Case in point, getting into safe mode on WinXP.. you have to be holding down F8 before it even tries to boot from the hard drive, or you'll miss it..
 
thanks guys...update: I got into bios, but only if i disconnect the HDD. When I was in BIOS, no HDD was detected, and if I connect it back up, when I leave BIOS, it stays on that screen.

So....bad HDD? I'll try the one from my current rig and let u know....:(
 
I've had comps seemingly lock up on me at initial start screen from bad hard drives or possible just not jumper'd correctly... what its doing is trying to determine just what the heck is hooked up to it so it can deal with it accordingly ..and its just having a hard time reading it
 
Switched to a HDD with windows xp on it (IDE from an old comp, but it's good) it detects the drive, tries to boot windows and I get the BSOD....damn.
 
Grimdj said:
Switched to a HDD with windows xp on it (IDE from an old comp, but it's good) it detects the drive, tries to boot windows and I get the BSOD....damn.


well, that's kind of a different problem all together.. you're trying to boot windows from a hard drive that was intalled on a completely different motherboard.. You're going to get a BSOD..

But, the import thing is that the drive was detected, and it tried to boot..

hard to say if the SATA hard drive is bad or not.. have you tried it on other SATA connectors, to rule that out? Too bad you don't have another SATA drive to verify that there's no problem with the SATA controller on the mobo..

probably a bad drive though..
 
It will let me into bios if the HDD has no power connected (either one) when the power is connected, the SATA drive just cycles non-stop as if searching. Tried all the SATA ports, same deal. Gonna take the whole thing to the shop tomorrow, and have them check the drive first. Thanks all, I'll let you know!
 
If you figure out what went wrong, please let us know. I've had the same problem with the setup in my signature: I had the DVD-RW at master on IDE0, and the two SATA drives on channel 3 and 4.

The DVD-RW was recognized in the POST, but neither SATA drive was, and the POST would hang at "detecting IDE drives" after it got to where the SATA drives should be.

If I took one of the SATA drives out, the other one would be recognized, and everything was fine. If I put the one that I took out back in, and took the first one out, it didn't see it. Changing SATA channels didn't work.

I just got these drives on Monday (4 days ago), and tried all this on Wednesday (two days ago, when I built the machine).

I've RMA'd the drive that wouldn't be recognized. When I get the new one, I'm going to do the following:

1) Take out the working SATA drive, and put in the new one, to make sure it's recognized on its own

2) Put in both SATA drives, and disconnect the IDE drives, to make sure both drives are recognized

3) Connect everything, and see if the two SATA drives are still recognized.

Hopefully, they'll both work this time.
 
I had a very similar problem when running drives on SATA1 and SATA2. The drive on SATA2 would make wierd noises and the MB would halt on the BIOS screen. I moved that drive to SATA3 and it seems to be just fine now.
 
Back
Top