Mod Me!! -- From multimeter to SFF

If you wanna get that meter working for something, you could always find a compute display that already uses analog meeters (such as a coolermaster musketeer) and take it apart and probably just hook your meter up to replace one of the stock meeters. You might want something cheaper but this seems like it'd be pretty easy to do.
 
Not quite an update..

I got me a Drill press stand at the flea market ($10 woot!!) Now i can make straight holes. I may re-do the mobo tray, but what I am doing now is making some braces on the back of the mobo tray. These braces will make the tray more sturdyand will add another support for a mobo stand-off. Also, the DVD-CD and the PSU will bolt on to these. The PSU is wide open right now. I made a new hole to get the cables out and I removed the plug-in socket. I will move the socket to the back of the computer where it is easier to reach. What has me concerned is the ventilation on the PSU. I will install it vertically so that one fan sucks in air from the bottom, and the exhaust fan goes on the top. Now, should I make a hole so that the fan extracts the air to the outside? (I will have to make a nice grill if so) or should I make some kind of "shroud" so that the exaust air is directed to the existing "louvers" (I dont want hot air recirculating inside the case).

Now, for those of you who think I am moving slowly on this project, you are right, and I have two reasons. First, I work on my balcony, and Albuquerque is quite cold for me at night (im used to Florida weather). Second, I like CS:source very much and the Shuttle I "gave" my girlfirend plays very well :D
 
My dremel just went up in flames!! :(
I was cutting some 1/16th aluminum "L" to make rails for the HD and the DVDRW when Poof!! flames started coming out the vents on the side of the dremel. It's late now, but I will take a picture tomorrow of the set up (althoug you cannot see any damage to the dremel itself). I think I will go to walmart and spend $20 in a REAL(cheap) reciprocating saw instead of using the puny dremel attachment.

I am modifying my PSU so that i fits "upright":
I have cut some power cables I did not need to make some room. I also have re-routed the cables so that they come out the side of the unit instead of the bottom and I have swaped the "intake" fan and the plug. The power cord now will attach to the side of the PSU (just oposite to the PSU cables) and both fans in the unit are on the top of the PSU exhausting hot air. I will take pictures tomorrow as well.
 
Oh, I almost forgot!!: Yet another sighting of an HP multimeter! :eek:

If you watch Constantine, the "gadgets guy" has one like this multimeter in one of the shelves right at his desk, so keep an eye out! :cool:
 
Here are those pics..

This was my dremel fixture so that i could cut the aluminum L-beams..
Deaddremel.jpg


This is what the PSU is looking like. It's almost finished, I just need to heat-shrink those cables together and close it up.
newPSU.jpg


Oh, yeah! notice something? uh-huh, thats right! I got a digital camera so that the pictures are actually worth looking at.
 
I can't wait to see this one finished, been watching it since it started :D
 
I have been working here and there, but I wanted to finish it before posting anything.

empty_rails.jpg


I made a HDD/CD rack out of some aluminum "L" bars. I used JBweld, the hard part was to keep the rails straight and in the right place. In the end one of the CD rails was a bit crooked, no biggie. Making the holes was also very tricky and in the end... well they do work anyway. What saved me here is that I made the holes oversized so that I could install grommets. That will help keep the sound generated by the HDD low. Still, I got one of the quietest drives I could find, a 120GB Seagate barracuda 7200.7. Overall, I am not very happy with my craftmanship, but hey, look at it. it works, so I am happy.

drive_rails.jpg


So, now I can actually see how everything fits :D :

front_right_top.jpg

built_back.jpg

built_frontleft.jpg


Now, I have some bad news that are actually good news :confused:
The drive rail is set too close to the front, so I have no room for the cables to get from the front to the back. This is good news because I have to re-build the rail, and that means I have a chance to improve in all the little things I did not like. :)

So fortunatelly, I will get some work done over the weekend.... riiiight! (as in: I wish but I don't think the GF is gonna let me :()
 
The project looks really good man. First post on [h], and its yours. You may or may not recognize my name. Just wanna drop you a cool idea i had. If you had a VFD emulating the old analog movement, that'd be pretty neat, as well as modding the old faceplate's connectors (the big heavy amp plugs) with multipin connectors for use as the keyboard and mouse or maybe even USB.
 
This is really looking sweet. I'm glad you kept the slide-out feature for carrying the MB. I'm eager to see how the finished piece will look.
 
Starbuck3733T said:
The project looks really good man. First post on [h], and its yours. You may or may not recognize my name. Just wanna drop you a cool idea i had. If you had a VFD emulating the old analog movement, that'd be pretty neat, as well as modding the old faceplate's connectors (the big heavy amp plugs) with multipin connectors for use as the keyboard and mouse or maybe even USB.


Actually, your name IS familiar.. bit-tech maybe?. And, yes, I am toying with the idea of customizing the mouse and keyboard connectors Zapwizard-style.
 
I used to have one of those meters, and IIRC, I have an old heathkit ociliscope somewhere. I might have to do some searching tonight. :p

I love the idea, and looks like you are putting it together nicely.
 
Disarray, if you are going to try somehting like this, measure closely, this microATX barely fits inside. And definitelly consider a slim CD and maybe even a 2.5in HDD.

I really hope this case comes out the way I imagined it, i like how it is coming along.


Starbuck3733T!!! I was right, just the other day I was reading about Goliath, lots of catching up to do. By the way, I love your avatar, what movie is it?
 
Yeah, that DVD burner cost me over $100 (compare to ~$46 to a regular one). But I had to go slim, a full-sized DVD was too large for this case.

I finished the new HDD rack over the weekend (barely had time) but I have been too busy to post pics. I'll try to post them tonight.

I also added the 2 bars to make the tray more robust, plus I will hang a green Cold cathode from one of these. I am really aching to put this baby together, Wifey does not know what she is doing to me by keeping me away (yeah, we did the court papers yesterday, its official. Although the wedding is in July)
 
Here are the pics i promised, i made them small 'cause there's a bunch of them
The new HDD rack:
new_raila.jpg

new_railb.jpg

The new braces:
bracesa.jpg

bracesb.jpg

My modded tool:
I bought the I-go electric screwdriver for $6... It sucks... Until i modded it :D
I cut the spare-bit holder to make room and added an extra battery (all taped up in the pic) for more speed and torque.. SWEET :D
i_go.jpg

i_go2.jpg


Ok, so I put it together again, here is how it goes:
you get the tray on its back:
back_tray.jpg

you add the PSU (here you see the back of the PSU, I made 4 holes in the case and JBwelded 4 nuts so the screws can hold on to the PSU)
PSU_railsa.jpg

tray_1.jpg

Install the DVD and then the HDD in the rack, and the rack onto the frame..
tray_4.jpg

Now I had to take the PSU out to attach the backside to the mobo tray ::mad::
tray_5.jpg

And finally the front and the braces
tray_6.jpg


I tested the mobo and ran some cables.. they fit now :) I also realized that I am not done sleeving. I need to sleeve the cables to the Cold Cathode and the power adapter to the SATA HDD.. and once I am done, I am sure I will find something else that also need sleeving..
tray_7a.jpg

tray_7b.jpg
 
i was orriginally gonna post about not seeing the power conector (fearing that it may jut straight out the bottom) that goes to the wall.. but i found it, how ever, did you leave enought room to get the cord to bend out (im assuming your gonna run it to one of the larger holes out the top) and even still it looks like it may be blocked by one of your brackets (just a littel.. nouthing a littel dremeling wont fix )

while i assume you used that orrientation for mounting the psu dvd and HD it looks almost like the holes on the psu would have lined up equally with the ones on the back, there by exausting the heat without any extra fans/work (ducting) ect.

just a thought i know you have put alot of work into the trays for mounting these, and keeping the front intact, and they fit the way they are, but if you turned them both on there side you should be able to get the fans to blow out the back and have the dvd eject out the back as well and keep even more of the orriginal shell intact...

unless the dvd rom wont fit side by side with the psu mounted that way... in which case there is always the option of mounting it on the other side of the case (mobo side) on its own tray ... unless you have plans for the PCI/AGP slots (if you could use parts that arnt full hight, then it may not matter)

i only wish i had thought of this when i first saw the thread, but didnt think of it then (didnt see the problems any way...)

thore
 
Holy crap!! nice mod, love how you built the custom frame because i am a big fan of anyone how can custom build stuff like that.
 
Thore,

I was too eager and I did not plan enough for this mod (i have some cuts/holes that i should not have made). The optical drive could not open on the front because the meter and the knobs are there, and if It opened on the back it would be difficult to get to. Having it upright was the only way to go.

Unfortunatelly, the PSU was too long to sit at the bottom, but it was just short enough to set it upright, like the optical drive. But the cables were sticking out, thats when I decided to open a hole on the side of the PSU to get the cables on the side and the power socket as well. I moved the socket to the bottom of the PSU b/c out the back of the case there is a grill on the top and a hole at teh bottom. I just have to make that hole slighly larger so the power cable can get through (no more bad holes, so i am waiting until i am 200% sure). Of course, moving the socket meant that I had to move the "intake" fan to the top side and make it a second "exhaust"
 
Ozone77 I am really impressed with how clean that framework appears in your pics. I know you'd probably do it differently if you had the chance to do it again, but it still stands out as a great effort. I'd really like to see how this all squeezes into the case. :D

I'm also hoping that your MB stays nice and cool, and you aren't forced to do anything dramatic to get more air in there. Keep up the good work!
 
Gee, thanks themark..

but you should see the old pics, the frame/ board was there already, I just cut it up and pieced it togeher so that all the parts could fit inside the case
 
OK, I realized that if I do not pick up the pace my parts will be obsolete before I finish. :D

First off, the PSU was sitting too low to connect the power cord once the case was closed, so I made new PSU rails (wider ones):
newPSUrails.jpg

Backside of the PSU on the rails
newPSUonrails.jpg

The PSU now sits higher, even the cables can come out the bottom..
newPSUup.jpg

I also made the hole on the back to connect the power cord (dark hole at the bottom)..
newPSUout.jpg

I tried cutting out a Molex and crimping instead a SATA power connector, but it did not work..
make_serialATX.jpg

I just sleeved the Molex-Sata adapter that came with the case. (no pic yet)
Finally, I put three 100Ohm in parallel to get a 33Ohm resistance, I used these on the PSU fans to lower them to 10v, they are not screaming loud anymore.
33ohm.jpg

Grabbed the stock fan, removed the thermal pad and added some Artic Silver 5 (just a bead, then I spreaded it out
stock_fan_articsilver.jpg

This sucker is LOUD It is spining at max speed to keep a the temperature at 75 C (VERY hot). Maybe the Heatsink is not making good contact?

So, I stole some switches and lights from an empty case and this is my temporary set-up (the PSU is recovering from an operation.) As I type this, I am formatting the HD to install windows..
installing_XP.jpg


I still have plenty of stuff to do, but at least it is not a heap of useless parts and pieces.

Oh yeah, I was freaking out... the DVD did not want to open out! I tried different things, and finally, I lossened the screws... it opened! Turns out my screws are too long, and if tight, they press against the CD tray.

Also, the system shut down when I was in the BIOS... It was too hot, I put the Mobo horizontal so that the heatsink would sit tight against the proc.. its working now, but I need to get it working right.
 
yeah, i just noticed the pics.. I'll try to fix it later..

Update: half-way done. It turns out the university no longer offers webspace for (ex)students. I will upload the pics to my ISP so they can host them. I already changed all the links in the thread, but the firewall at work does not allow me to use FTP to upload them.

Well, there are a few pics that are not showing up, I may or may not fix that, since I dont believe they are critical, you can follow this project perfectly without them.
 
I need your input guys.
This is what the computer looks like right now, I put it together for a test fit. The wires sticking out are the on/off button, the switch controls the green cathode
april_iso.jpg


Where can I find connectors/knobs for the multimeter? If they look old like the originals, better.
The new HDD rack:
april_front.jpg
front.jpg


Now, looking at the back:
Should I cut out the pannel and have all the I/Os in the back open?
Should I just cut out the ones I need? (keyboard, usb, lan?)
Should I make some extender cables and make the connections in the front for kb, mouse, headphone/mic.?
Should I cut the window out and use a piano hinge to make it open/close like a door?
what else could I do?
april_back.jpg
 
ok.. im gonna chime in here this time and not let you mess it up.. :p

did you keep the original knobs??? if so i would use the middel knob for fan control, that said, if you didnt keep them it looks very much like a knob you can get from radio shack, but if your gonna buy a new one better looking knobs can be had (ill do some looking here in a few) , also.. figure out what voltage that needel runs at (start with like a 1.5v battery and see if that pegs the needel.. work from there) and run it from the same potentiomiter,(use a 25ohmer for up to 90mm... i have used em for 120mm's but they get damn hot at low power... i wouldnt expect them to last long) ,

as for power... move it up one spot and use the power for power... (duh) make input usb ports (2 stacked on top of each other... unless you would rather use that for for keyboard /mouse... wait.. usb keyboard/mouse... problem solved :D)

the hole just below zero should be reset.. if you ask me..

output=earphones...

outputlevel... not shure.. maybe a pot for controling (fine tuning) the needle

there is a hole to the left of output that is screming to have an LED put in it... take the screw out of the other one and fill with LEDs of your color likeing..

powerlight = powerlight.. :p

now... for HD activity... i would put the hd leds (thats right.. more than 1) in the corners of the window (at least 2 in the 2 top corners, where it wont interfear with the movement of the needel and can still be hidden by plastic (it should give it a "faulty light" effect during hd activity) andsee if you can light the bottom of it with LEDs that will stay on (err.. on with power that is)

as for the back.. if you use the front usb for keyboard/mouse.. then i see littel reason to exspose it.. other wise go for it.. (but just what you need...)

i was under the impression that you would have the cdrom come out throught the top of the case.... but it looks like you decided to go the route of remover the shell to gain access to it .. meh.. forgot where i was going with this..

i would love to see light come flowing out of all of thoughs vents.. i dont know how your going to do it without impeading airflow.. (your gonna need every ounce of air you can in that thing.. ) if your going to do any thing to the back it should be to put some fans in..


thats all i can think of for now..

thore
 
Well, I kept all the switches/connectors... except for the main one, it was imposible to take out, so I had to cut it into pieces... :(

Power light is power light righ now, I took out the lightbulb from the casing and inserted the power LED.

In the front, I would like to have headphones, mic, KB, mouse and at least one open USB..
hp and mic can go to the ouput and output level, but I will have to get creative to squeeze the USBs in the input port.

I kept the vernier zero knobs and pots, I was thinking of using those to control 2 fans, or I could control the needle as you said.

Since I dont use the power switch much, I was thinking of sticking it in the back (no reset buton).

The CD will open to the top, but I had to put it in place to figure out where I need to cut the shell.

Those ideas for the meter are fantastic, I will consider them once I have it working... speaking of wich, what do you mean by "25ohm for 90mm"?
 
Ozone77 said:
speaking of wich, what do you mean by "25ohm for 90mm"?


the pots are rated for ohms the higher the ohms the faster the sweep say you use a 100ohm pot the only about the last 1/4 of its action will be used (or i have it backwards and if you where to use a 1 ohm pot you would get this effect.. i dont remeber.. been along time, all i know is 25ohm works).. as for the 90mm part is was directly relateing it to the size of the fan as you have to watch the wattage draw a 90mm dosent darw enought to burn up a pot... (as you decrease the voltage the fan trys to grab at more amprage to compensate this creats heat,and is there for dissapated in the pot) most 90 mm fans draw very li9ttel power.. (as long as we'er not talking tornadows or dealta screamers here) where as 120's can draw over 1 watt... when you drop the voltage things get very hot very quickly.. my sunnon draws almost 4w and and makes a 25ohm 3 watter very hot very quick at its lowest power... i had to jumper the pegs of the pot (rheostat acctually) with a resistor to keep it from droping below (or riseing above rather) the maximum of the pot (i think i used 2 15ohm 1/2w twisted together... but i dont remeber... )

http://sound.westhost.com/pots.htm
that will get you started
http://www.radioshack.com/category.asp?catalog_name=CTLG&category_name=CTLG_011_002_011_000&Page=1
the one im talking about

im shure i got some of my stuff wrong... any way.. im shure you get the point..

any way.. if you decide to run the fans off a pot i have ran 3 80's off a 25ohm 3w pot without any trouble... but 4 seem to be to much they start acting wierd, feel free to play with different ones, just watch your wattage rateing... it wont damage your fans to do so , but if it shorts out it could take other stuff with it... (if your unshure figure out the maximum amp and voltage draw and put in quick blow fuses at just over the max amps on both positive and negitive lines (get a radioshak prototypeing board, and proto board it to save time) it may save your ass..

i run an aerogate now for fan contol... so i dont have the pots/resistors to look at any more to give you the numbers to go by, any way.. read the first link and if you still have questions fire away and ill do my best

thore

/edit... just relized why you asked that.. lol. sorry... i was tired when i was writeing that... kinda ran two thoughts together there... ment to say use a 25ohm pot for upto 90mm fans and run the meter off the same pot so that fan speed and needel movement scale at the same rate... you wont be able to run the needel at the same voltage as the fane..12v will most certanly fry it... (if it isnt dead already....i dont remeber you saying it worked.. but.. i havent gone beack to reread it eather.. :| ) so you would have to run the fan directly off the pot and use a resistor to drop the voltage to drive the needel... (not the right way but it works and is cheap (if someone else wants to chime in here with a better method now is the time.. :p))
 
Ozone77 said:
I kept the vernier zero knobs and pots, I was thinking of using those to control 2 fans, or I could control the needle as you said.
Why not both? Run the two fans off the same circuit (if you use the pot that thore is suggesting, make sure that their total draw is no more than a quarter amp-- just go to radio shack and get a cheap@$$ ammeter) and use the meter to show how much juice you're putting to the fans.

Or, better yet, use the meter with one of those PC Tachometer kits. You'll probably need to do a little wiring to get it to work right, but it shouldn't be too too hard.
 
Back
Top