Mobo problems

DocFaustus

2[H]4U
Joined
Sep 22, 2002
Messages
2,830
Hey guys. I just got my new DFI Ultra Infinity yesterday and hooked up my new rig. I fired it up and much to my dismay nothing happened. The board is getting power, the system fans plugged into the board are spinning up, harddrives are coming alive, video card fans and lights do thier thing.

The monitor never comes on. At first I thought it was the monitor, so I moved the monitor to another computer it worked fine. Then I did the same thing with the video card, it also works fine.

I decided to plug in the system speaker to see if it will tell me anything. Nothing, no beep at all. To try to force a beep, started it up without a video card, still type of beeping, started without ram, still no beeping, I even pulled the CPU and powered it up, no beeping at all.

I have reset the CMOS many times to no avail. Can I call this board DOA, or am I missing something I should try?
 
Are all your IDE connectors in the right way? Just in case you are using an older ATA33 cable for one of your CD drives without the notch, you might have one of those in backwards.
 
Nothing plugged into the IDE slots. I never bothered plugging in the CD-Rom drive. And both of my harddrives are SATA.
 
Even though its a DFI board, its probably not DOA. This sort of issue is common for installation errors. I would remount the processor, and make sure it isn't chipped. In a situation like yours, its almost always an issue with the mounting/installation of the CPU. Make sure the chip still works in your old board.
 
Oh yea, this chip kicks much ass, I threw it in my A7N8X and immediately pushed it to 2550 and let it prime overnight. when I get home from work, I will see how far it can go.

I also threw my BFG5900NU back into my other rig to make sure it wasn't somehow damaged, it runs like a champ too.

Moved the swapped monitors with my other rig, it works fine.

Unplugged the SATA drives all together to make sure something wasnt funny there.

I even took the new power supply and made sure it could power my old system. It passed with flying colors.

I have tried the ram in slot one, then slot two, then no slot at all. Still no luck. When I get home I will put the new ram into my old rig just to say I did it. But I am sure it will not make a difference.

I still am getting no video and aside from power coming on, no proof that there is any life at all in this board. And yes, fans connected to headers on the motherboard do spin up when I apply power. Still with all the attempts I have made, not a single beep out of the speaker.
 
Try resetting the BIOS, then holding INSERT as you power up. A wonderful trick on the NF2 boards.
 
Had the same problem when I got my DFI board, the problem was the ram. After doing some borrowing and swapping from other machines I found some that worked. Seems that there boards are alittle picky when it comes to that.
 
Originally posted by Schro
Try resetting the BIOS, then holding INSERT as you power up. A wonderful trick on the NF2 boards.

Tried that. I even pulled power, popped out the battery, and shorted the jumper. Thanks though.
 
Originally posted by Stynger
Had the same problem when I got my DFI board, the problem was the ram. After doing some borrowing and swapping from other machines I found some that worked. Seems that there boards are alittle picky when it comes to that.

When you had the problem with the ram, the board just did absolutely nothing? I have had bad ram before, but there was always an error or indication.

BTW, my ram is a single stick of 512MB Mushkin 222 special BH-6
 
It didnt post any errors or if it did I had no video to see it. Think the brand I had from Microcenter at time of purchase of the mobo was Centex or Centron something like that, but that was the problem.
 
Thanks for the suggestions guys. It turns out the mobo was in fact DOA. My replacement came today and it fired right up.
 
Back
Top