Might need a new mb

Benzino

[H]ard|Gawd
Joined
Mar 3, 2005
Messages
1,713
I have a Giga-Byte 8IPE1000 Pro Rev 2 with a Pentium 4 2.8 gig processor (800mhz fsb). Last week, I decided to go into the BIOS and increase the multiplier. If I had bothered to research it, I wouldn't have done that, but I did. My computer shut down, and has yet to start. I conversed with some people at Gen[M]ay forums, and they recommended to reset the CMOS. I spent all week pulling out the battery, puting it back in, and other methods to reset the CMOS, and none have worked. I even contacted Giga-bytes support line, and they recommended the same. I have concluded that the CMOS is not the problem. This leaves me with a dilemma between two choices.
1)Continue to research the problem and a solution in hope to fix it without spending any money.
2)Assume my current mb is trashed, crack it over my knee (ouch) and buy this one at Newegg.
I'd prefer #1 if I can find a solution here, but if all else fails, I will reluctantly go with #2. I didn't find much help at Gen[M]ay forums, so I figured I would have a try here.
Suggestions? Comments? Help?
 
Does your board have a jumper for clearing the bios? On my Chaintech board I could leave the battery out for a week and put it back in, only to have the same settings there. My board has a jumper that you simply switch the placement of it for 15 seconds and then power it up, power it down and then put the jumper back the way it is supposed to be.

Check your mobo manual to see if it does. And not to be a butt....but you did remember to unplug the power cord, wait 30-45 seconds then put the battery back and then the cord, and then power it up.
 
Well, I checked the manual and contacted tech support from Giga-byte, and they both said that you have to pop out the battery. It said nothing about a jumper and I couldn't find one either. That is definitely not it.
As for unplugging the cord, I've tried that repeatedly.
As I said before, it seems taht the problem lies not within the CMOS, but something else. I might need a new mb alltogether, unless its something else.
 
Okay... this is very strange.

When I read your post, I (sorta) rolled my eyes, thinking "some people really shouldn't assemble their own hardware". Then I downloaded the manual for the board.

My god. The thing does NOT have a clear CMOS jumper!!! What the hell was Gigabyte thinking?!?! They have a clear password jumper (I would try that if you haven't already, it is marked on the PCB just below the memory). Maybe the guy that designed the PCB didn't speak very good english (password = cmos clear?)... I dunno.

If it doesn't actually allow you to clear the CMOS/BIOS, I consider that a MAJOR design defect, for the very reason that you might have to replace the board. Hell, I would consider RMA'ing it. That is plain bullshit. If you put a bad setting in the BIOS (as most/all overclockers have done MANY times) you should be able to clear it and start again!

Good luck!

PS: for all you "don't RMA the board cuz you broke it" people... if you have ever had to clear your BIOS cuz you put a bad setting in it, you can STFU. :)

-Skystalker
 
I tried the "Clear Password" jumper, just in case, and that didn't work either. I ordered from Mwave last January, so I doubt I could successfully RMA it. (I have converted to Newegg since then.) Unless anyone can convince me otherwise, I'm gonna order an Asus board to replace it. I haven't had use of my computer for an entire week now, and I don't want to spend the rest of March dickign around with the mb that I most likely fried anyways.
 
I don't believe it is fried...

Just bad CMOS/BIOS settings.

Their has to be a way. I have to go out for a bit, but I will carefully read your manual, and see what I can come up with. This is one strange problem!

<mumbles under breath> who the hell would design a mb without a jumper for this </mumbles under breath>

-Skystalker
 
Okay... I found it on page 31 of the online PDF manual (that can be found here.)

"If you want to erase the CMOS...

1.Turn OFF the computer and unplug the power cord.
2.Remove the battery, wait for 30 second.
3.Re-install the battery.
4.Plug in the power cord and turn ON the computer."

(copied exactly word for word... chinese english... ick)

Hope that helps... the key is unplug the power cord when you do this, or the CMOS will not be cleared.

If you have tried this before, you should try it again-- may save ya some $$.

-Skystalker
 
Skystalker said:
Okay... this is very strange.

When I read your post, I (sorta) rolled my eyes, thinking "some people really shouldn't assemble their own hardware". Then I downloaded the manual for the board.

My god. The thing does NOT have a clear CMOS jumper!!! What the hell was Gigabyte thinking?!?! They have a clear password jumper (I would try that if you haven't already, it is marked on the PCB just below the memory). Maybe the guy that designed the PCB didn't speak very good english (password = cmos clear?)... I dunno.

If it doesn't actually allow you to clear the CMOS/BIOS, I consider that a MAJOR design defect, for the very reason that you might have to replace the board. Hell, I would consider RMA'ing it. That is plain bullshit. If you put a bad setting in the BIOS (as most/all overclockers have done MANY times) you should be able to clear it and start again!

Good luck!

PS: for all you "don't RMA the board cuz you broke it" people... if you have ever had to clear your BIOS cuz you put a bad setting in it, you can STFU. :)

-Skystalker

Gigabyte has been doing that for awhile. Asus did it for awhile back in the day and stopped. I would imagine Asus board owners didn't like it.
 
Sir-Fragalot said:
Gigabyte has been doing that for awhile. Asus did it for awhile back in the day and stopped. I would imagine Asus board owners didn't like it.

I would imagine.

Hard to believe the manufacturer's would do that.

Oh, well...

-Skystalker
 
Back
Top