Memtest=0 errors but Prime95 fails

Joined
Aug 17, 2004
Messages
30
I have 1x512 K-byte ddr333 and 1x512 Crucial ddr266 in the following system

Mobile Athlon 64 3000+ 1mb cache @9*265=2.4ghz
9800 Pro @435/378

I overclocked the memory to 176 mhz(ddr352) 2.5-4-4-9-1t, and it went through 2 passes of Memtest86 with no errors. I was pretty surprised at the overclock on the Crucial stick, even though it is single-sided. When I booted into windows and ran Prime 95, I got a fatal error within 10 seconds.

To make sure the memory was the cause, I put the memory on a 2:1 divider (ddr266), and changed the hypertransport multiplier to 2x. I left the htt and multiplier the same @9*265. There were no errors after 4 hours of Prime95 with these settings.

Could this be an bug in Prime95 or is it my system?
 
I've upped the vdimm to 2.8, my motherboard goes farther, but i don't really want to go higher on ram that says it's max is 2.7. Would it be safe to run it at 2.9?

I have also tried upping the vcore, but like I said I'm pretty sure that the cpu is not the problem. The same setup at the same settings except lower ram speeds passes 4 hours of Prime95 with no errors.
 
yes, most ram can run 2.9vdimm even without a heatspreader. i would seriously look into buying some new ram though, if you are that interested in overclocking. try pdp systems ddr3200 2-2-2-5 with xbl technology. it uses the samsung tccd memory modules and a 512x2 set costs low 200's on newegg.
 
spaceheater184 said:
yes, most ram can run 2.9vdimm even without a heatspreader. i would seriously look into buying some new ram though, if you are that interested in overclocking. try pdp systems ddr3200 2-2-2-5 with xbl technology. it uses the samsung tccd memory modules and a 512x2 set costs low 200's on newegg.

I am planning on getting that ram or the gskill pc4400 2.5-3-3-7 when I can afford it. For now, I want to figure out why ram that gets no errors on memtest86 is not stable in windows. Now at ~ddr340 2.5-4-4-10 it doesn't even boot into windows, but still passes memtest86.
 
few things what psu are you running? is your pci/agp locked? lower everything back to default then try and see if it boots and passes prime95. If it still fails its one of two things. either bad ram, or a bad psu.
 
Qwertyman said:
few things what psu are you running? is your pci/agp locked? lower everything back to default then try and see if it boots and passes prime95. If it still fails its one of two things. either bad ram, or a bad psu.

I have a antec smart power 350 watt. I was thinking it may be the psu because no matter what i set the vdimm to in the bios, digidoc reports it to be ~2.44. My pci/agp is locked.
 
Qwertyman said:
yea smartpowers suck get something else
They're better than pretty much all the generic makes out there. I'm building an A64 939 setup for a friend, and utilized the SmartPower350. I was surprised to see that it outputs 21A on the +12V rail, where my TruePower430 puts out 20A on the +12V. I wouldn't exactly throw one out, they're pretty good power supplies for the money.
 
_Korruption_ said:
They're better than pretty much all the generic makes out there. I'm building an A64 939 setup for a friend, and utilized the SmartPower350. I was surprised to see that it outputs 21A on the +12V rail, where my TruePower430 puts out 20A on the +12V. I wouldn't exactly throw one out, they're pretty good power supplies for the money.
very true, but it stills leaves an opening that it could be it.
 
I have a P4 2.4c and OCZ 4000 DC Gold EL. I thought p95 crashing was sign of unstable OC BUT!!! what i found is that since I had a gig of ram, I disabled the page file and had no virtual memory. P95 sets a test size equal to that of your physical mem....meaning that the 120 or so megs of system processes takeup some space...and there is conflict...RESOLUTION....re-enable the PF and try again....if you already have it enabled...try getting new mem.
 
Back
Top