K7S5A won't boot correctly

T

Torn

Guest
Hey folks. Just got a new motherboard, so its not critical, but the reasons I replaced the old one was that it suddenly shut itself off and now whenever its booting up, it gets to Updating NVRAM...Failed then Windows wont boot and a BOOT disk wont even boot. I was, however, using a stick of RAM I know now to be bad (though the current mobo was at least booting with the RAM present). Do you think the RAM may have corrupted the BIOS chip or, seeing as how it is a cheap-o board, the BIOS chip just up and died? Also, I tried e-mailing ECS about getting a new one and they have NEVER responded at all. Anyone know where I might find a new BIOS chip? Thanks as always.
 
It could be the PSU, the ECS boards typically like nice amperage on the +5V because they use such shoddy VRMs.

I doubt the RAM could have corrupted the BIOS in any way. Have you tried to reset the CMOS jumper?
 
what version of this board do you have?? 1.0, 3.0 or 5.0(pro)??? The version 5.0 of the board seems to work very very nice for the price... version 3.0 not as well... will reset bios every month or so.... and version 1.0 STINKS.... had one that wouldn't allow me to run a cd-rom on the same ide channel as a HDD, no matter what HDD I used or CD-rom... wierd acting boards... anyhow try reseting the cmos by pulling out the battery for like 15 seconds or so, or by clearing it with jumper.... cause I have one that was a version 3.0 that almost everytime I added a new card(be it a modem, sound, or even ram) it would require me to reset the bios.... wierd eh??

QwertyJuan
 
I'll try resetting...can't believe I didn't think of that in the first place (DUH...). As for the PSU, I'm running an A7N8X-E with it now with no troubles (heh...at least NOW), but just to be safe, I'll check the BIOS and see where the lines are at. Wierdest thing is that I've been running it for a year and a half virtually untouched (but for the RAM change) and had ZERO problems with it up to now.
 
yeah that board has probs keeping its bios - do a deep clear ( clear cmos with battery removed for 30 minutes) if you look at the board they use the old fashioned bios chips, those sometimes keep a charge longer - so thus the deep clear.
Which version is it? the 1.x versions are notoriously sensitive on power , memory, and agp cards - I believe its because they got a lots of poorly made circuitry (I believe they were purchased just before the breaking of the story bout the fake tiawanese capacitors... I think ECS bought a bunch of those unknowingly) 3.x versions are much stable, the Pro edition even more. Check your capacitors and see if any are bulging, charred, or leaking (DONT TOUCH ACID) if so - bad board.
 
probably the psu, i had a shitty brand 350watt psu that caused random restarts and shittyness, but with a good name brand psu problems went bye bye. I actually am using my ol' k7s5a right now. its a good board, single chip design makes for great memory latency properties. It seems more responsive when running the same bus speeds than my kt400 board, which cost way more money.
 
Well, turns out my current PSU is only putting out 4.7V on the 5V line. Is that low enough to cause problems?
 
what version is it?
I had a ver 1.0 and it would not run with an PSU that was running 4.85 v on the 5 line so that could be the issue yet the 3.0 my neighbor had in theirs could run on lower voltage on the 5v line fine.
 
Originally posted by Torn
Well, turns out my current PSU is only putting out 4.7V on the 5V line. Is that low enough to cause problems?

Thats about 5% out. I know that ECS boards need a good PSU, but at 5% I would think that it might not be a problem, if the psu has a ripple voltage problem (noise) it might push that 5% over to where it's freaky for that ECS board...
 
Fairly certain its in the 1.X line...so maybe I just need a deep clear and a new PSU. :p
 
Thankfully, I am now running an A7N8X-E...unfortunately its with that same PSU. Works well now that I dumped the bad stick of RAM.
 
there where also reports that wierd bios type probs where cleared up by simply replacing the battery on mobo from the KVS(I think thats what they typically used) to a better quality battery ..ie Panasonic perhaps

mucho info on that board at ocworkbench.com forums under ecs
 
Originally posted by ThreeDee
mucho info on that board at ocworkbench.com forums under ecs
Definitely. My "temporary" K7S5A got a good once-over with the info from that site and the damn thing's still running strong over a year later. I'm tired of waiting for it to break so I'm going to upgrade anyway, but it's been a great board.

And yes, I DID get a new PSU (Antec True430) and replace the battery with an Energizer.
 
Back
Top