just started overlcoking, Does this look right?

galaxie83

n00b
Joined
Mar 14, 2010
Messages
57
My core voltage looks a bit high. Everytime I try to lower it, it's unstable and I get a blue screen. Should I lower the bus speed? Any help would be appreciated.
http://valid.canardpc.com/show_oc.php?id=1208871
4643603162_b9004bd36c_o.png


Windows 7 Ultimate Edition (Build 7600)
CPU Arch : 1 CPU - 2 Cores - 2 Threads
CPU PSN : AMD Athlon II X2 250 Processor
CPU EXT : MMX(+), 3DNow!(+), SSE (1, 2, 3, 4A), x86-64, AMD-V
CPUID : F.6.2 / Extended : 10.6
CPU Cache : L1 : 2 x 64 / 2 x 64 KB - L2 : 2 x 1024 KB
Core : Regor (45 nm) / Stepping : DA-C2
Freq : 3750.21 MHz (250.01 * 15)
MB Brand : Biostar
MB Model : A760G M2+
NB : AMD 780G rev 00
SB : AMD ID439D rev 00
GPU Type : ATI Radeon HD 2400 Series
GPU Clocks : Core 700 MHz / RAM 500 MHz
DirectX Version : 11.0
RAM : 4096 MB DDR2 Dual Channel
RAM Speed : 250 MHz (1:1) @ 4-3-3-9
Slot 1 : 2048MB (6400)
Slot 1 Manufacturer : Nanya Technology
Slot 2 : 2048MB (6400)
Slot 2 Manufacturer : Nanya Technology
 
meh, the Athlon II X4's i know will hit 4.0 with that voltage, not sure what they need for 3.8, but i would think thats about what ya need.....though you RAM is dead slow :p, maybe i am misreading it ?......

anyhow, it could also be your board, that can have an impact on how much voltage is needed for higher clocks
 
Regors are probably made from worse silicon than the X4's so I wouldn't be surprised if it is near its aircooling limits. Since you are on a single-plane motherboard the CPU-NB is getting the full 1.5v+ that the cores are so that can't be holding you back. Is your memory really running that slow? I tried looking Nanya up and I could only find what looked like OEM parts of DDR2 5300 or below. Was this from a combo deal? That is the motherboard MicroCenter is giving away for free with CPU purchases right now.
 
looks like its ddr2 6400 based off the information.. if thats true then they are running insanely slow.. my guess is you have them running at ddr2 200(400mhz) if thats the case then you will want to raise the memory to ddr2 333mhz or ddr2 667 in the bios which ever option it gives you.. this will give you ddr2 820ish or ddr2 410mhz so you may have to raise the voltage just a tiny bit on the ram or run it below spec and set it at ddr2 533 or 266mhz..

your HT link is also to low.. it should be running at 2ghz.. or 10x in this case it should be set to 8x which gives you 2000mhz..

if its a single plane motherboard then the cpu's going to require more voltage then what would be needed to overclock on a dual plane motherboard so 1.53v sounds about right.. the limit AMD states for the 45nm chips is 1.55v.

and last but not least.. what are your temps at full load?
 
See this is why I come to you guys. Your all so smart about this. I'm obviously just starting out.:)

I didn't realize my ram is running slow untill you guys mentioned it. I'll try raising it up and see how it helps as well as the HT link. I stress tested the cpu for 2 hours using prime95 and my temps maxed at 41c. I heard of people overclocking these CPUs as high as 4.8 so that was what I was shooting for.
The bios screen is a little confusing to me. Here is what I have the bios set at.
CPU Overvoltage
This item allows you to select CPU Voltage Control.
Options: StartUp (Default) / +0.10V / +0.20V / +0.30V
Memory Overvoltage
This item allows you to select DDR Voltage Control.
Options: 1.95V (Default) / 2.05V / 2.15V / 2.25V / 2.35V / 2.45V / 2.55V / 2.65V
Chipset Overvoltage
This item allows you to select NB/SB Voltage Control.
Options: 1.15V (Default) / 1.20V / 1.25V / 1.30V
Should i mess with the chipset overvoltage setting?
HT Overvoltage
This item allows you to select HT Voltage Control.
Options: 1.20V (Default) / 1.30V / 1.40V / 1.50V
CPU Frequency
This item allows you to select the CPU Frequency.
Options: 200 (MHz) (Default) / 200-600 250
Memory Clock Mode
This item allows you to control the Memory Clock.
Options: Auto (Default) / Limit / Manual
Memclock Value
This item allows you to set the Memory Clock.
Options: DDR2-400 (Default) / DDR2-533 / DDR2-667 / DDR2-800
HT Link Speed
Options: Auto (Default) / 200MHz / 400MHz / 600MHz / 800MHz / 1GHz
HT Link Width
Options: Auto (Default) / 4 Bit / 8 Bit / 16 Bit

I baught all of this off a guy on craigslist. He had it all setup already, So I took everything out of his case and transfered it over to my 800D case. Since I'm still saving up to put nice stuff in my 800D case I just got this for now. I am using all the stock cooling exept 3 120mm apevia fans I added to the case for the exhaust. hopfully in the next month or so I will be getting the I7 920 and the Asus Rampage III.
 
Last edited:
See this is why I come to you guys. Your all so smart about this. I'm obviously just starting out.:)

I didn't realize my ram is running slow untill you guys mentioned it. I'll try raising it up and see how it helps as well as the HT link. I stress tested the cpu for 2 hours using prime95 and my temps maxed at 41c. I heard of people overclocking these CPUs as high as 4.8 so that was what I was shooting for.
The bios screen is a little confusing to me. Here is what I have the bios set at.
CPU Overvoltage
This item allows you to select CPU Voltage Control.
Options: StartUp (Default) / +0.10V / +0.20V / +0.30V
Memory Overvoltage
This item allows you to select DDR Voltage Control.
Options: 1.95V (Default) / 2.05V / 2.15V / 2.25V / 2.35V / 2.45V / 2.55V / 2.65V
Chipset Overvoltage
This item allows you to select NB/SB Voltage Control.
Options: 1.15V (Default) / 1.20V / 1.25V / 1.30V
Should i mess with the chipset overvoltage setting?
HT Overvoltage
This item allows you to select HT Voltage Control. <--- this you can leave at the default 1.2v
Options: 1.20V (Default) / 1.30V / 1.40V / 1.50V
CPU Frequency
This item allows you to select the CPU Frequency.
Options: 200 (MHz) (Default) / 200-600 250
Memory Clock Mode
This item allows you to control the Memory Clock.
Options: Auto (Default) / Limit / Manual
Memclock Value
This item allows you to set the Memory Clock.
Options: DDR2-400 (Default) / DDR2-533 / DDR2-667 / DDR2-800 <-- change to DDR2-533 or DDR2 667
HT Link Speed
Options: Auto (Default) / 200MHz / 400MHz / 600MHz / 800MHz / 1GHz
HT Link Width
Options: Auto (Default) / 4 Bit / 8 Bit / 16 Bit

I baught all of this off a guy on craigslist. He had it all setup already, So I took everything out of his case and transfered it over to my 800D case. Since I'm still saving up to put nice stuff in my 800D case I just got this for now. I am using all the stock cooling exept 3 120mm apevia fans I added to the case for the exhaust. hopfully in the next month or so I will be getting the I7 920 and the Asus Rampage III.



i edited within your message which is why its not quoted..
 
you will not hit 4.8 GHz with that setup, atleast not on air......the people hitting 4.8 GHz are using water at a minimum(probably L2N....for max overclocking)...and in no way would I feel safe using the voltage necessary for 24/7 operation(assuming it is stable)....


also, try the changes that sirmonkey suggested, they may help you get a little more speed within the system itself
 
I think that did it.
4646103044_fde1efcc4e_o.png


RAM : 4096 MB DDR2 Dual Channel
RAM Speed : 417 MHz (3:5) @ 5-5-5-15
Slot 1 : 2048MB (6400)
Slot 1 Manufacturer : Nanya Technology
Slot 2 : 2048MB (6400)
Slot 2 Manufacturer : Nanya Technology

Thank you guys very much for your help!

To W.Feather, Sorry that was a typo, I meant 3.8ghz not 4.8ghz. I think I would blow up the processor if I attempted that lol.
 
looks like a solid overclock :)

even your RAM is finally up to speed (i believe that is showing it at a hair over 800 MHz), and no problem :p those chips will hit 4.8, but only under extreme cooling...


now, is your system stable??? might want to make sure of that by running some IBT(intel Burn Test), Prime, and LinX
 
I got the same CPU & MOBO that u have galaxie83,Mainly just for my secondary rig and I've got mine running @ 3.75 right now and running Prime95.So far I'm 20 mins. into a 3 hours stability test,Will let you a know if it stable when I'm done and where my setting are at.
 
Since this is a temporary setup there is really not to much to worry about.Long term;I think the cpu and mermory voltages are being run on the ragged edge.1.95 volts on memory should suffice.At 2.15v,unless the memory is set to handle,there is the possiblity of extensive parts damage.Are you using a program that will monitor cpu and nb temperatures?
 
Last edited:
I think that did it.
4646103044_fde1efcc4e_o.png


RAM : 4096 MB DDR2 Dual Channel
RAM Speed : 417 MHz (3:5) @ 5-5-5-15
Slot 1 : 2048MB (6400)
Slot 1 Manufacturer : Nanya Technology
Slot 2 : 2048MB (6400)
Slot 2 Manufacturer : Nanya Technology

Thank you guys very much for your help!

To W.Feather, Sorry that was a typo, I meant 3.8ghz not 4.8ghz. I think I would blow up the processor if I attempted that lol.

now the numbers look correct.. nice job..

and like DrDoU said.. the ram voltage might be a tad high.. does this ram have heat spreaders on them? if not i would consider trying to drop the voltage to 2.05v first to check for stability and if possible drop it to 1.95v.. because if there is no heatspreader this ram wont last very long at that voltage.. now if they do have heatspreaders then the voltage should be fine..
 
Ok,here it is;Athlon II x2 250 overclocked to 3.85(3 hours Prime95 stable,

CPU Clock: 257
CPU OV: +0.20v
Memory OV: 2.05v
Chipset OV: 1.20v
HT OV: 1.30v
DRAM Timing;
Memory Value: DDR2-667
CAS(CL): 5
TRCD: 5
TRP: 5
TRAS: 12
TRC: 22
Command: 2T
HT Link Speed: 1.6GHz
CPU FID/VID Control:Custom P-State;Enabled
Core FID: x15.0 3000MHz
Core DID: Divided by 1
Core VID: 1.3500v
NB FID: 2000MHz

Proof:
AthlonIIx2250_3HoursStable385.png
[/IMG]
AthlonIIx2250_3HoursStable385_Pic2.png
[/IMG]
 
Hey guys sorry it's been sometime since I been on here, Busy this past weekend.
AMOCO I will try those setting tonight. And Run Prime for 3 hours just like you did and post my result. Really appreciate all the help guys.

DrDoU I have a couple couple programs I use to monitor. One is the CPUID and I was using Speedfan, but I just recently downloaded this new and I cant remeber the name. I post it on here later. It works alot better than speed fan imo.
 
My overclock is similar except I've got a 240 x2. Also I run 3.5GHz (250 x 14mult) at default cpu voltage. Voltage is somewhere around 1.35 or so.

I'm certain more voltage would yield me faster clocks, but I don't wish to stress my board's power regulation any further. My next step for the OP would to start dialing back the voltage and see where you lose stability. Make that overclock as efficient as possible ;)
 
Hey guys sorry it's been sometime since I been on here, Busy this past weekend.
AMOCO I will try those setting tonight. And Run Prime for 3 hours just like you did and post my result. Really appreciate all the help guys.

DrDoU I have a couple couple programs I use to monitor. One is the CPUID and I was using Speedfan, but I just recently downloaded this new and I cant remeber the name. I post it on here later. It works alot better than speed fan imo.

try CoreTemp this a excellent program.
 
Well I hope these setting help galaxie83 and anyone else that it helps,Enjoy all,
Push it to the Limit(Overclocking)
 
I own an Atlhon II 245. I hit 3.5 on default voltage and 3.625 at 1.4v.... your voltage is too high for comfort IMO. If you want to push it that high then it's your choice, but i would never add .2v for a 250mhz increase. What is your highest OC on default voltage?
 
Last edited:
I own an Atlhon II 245. I hit 3.5 on default voltage and 3.625 at 1.4v.... your voltage is too high for comfort IMO. If you want to push it that high then it's your choice, but i would never add .2v for a 250mhz increase. What is your highest OC on default voltage?

Volts any lower and it won't even run OCCT for 5 mins. before it crashes.The volts I'm running on this CPU are well within reason for my overclock of 3.85 Stable.
But,first and foremost Get an aftermarket CPU Heatsink & Fan or fans.
This is the Heatsink I'm using on this CPU(Athlon II x2 250);;http://www.xigmatek.com/product.php?productid=16

My full load temps never exceed 40c with an ambient 78ºF
 
Last edited:
Then that's the max you can get out of it...If you're doing everything correctly
 
Back
Top