Just Built System, Shuts Down after 30 seconds...

ShredderFan

Limp Gawd
Joined
Jul 2, 2006
Messages
133
OK all, here's the setup..

Asus P5n32-SLI Delux Motherboard
PNY 1GB Memory DDR2 667
LGA 775 Socket T Intel Core 2 Duo 2.4 GHZ
Antec True Power Three 650 Watt Power Supply with 20pin+4 connector
ATI AIW X1900 Graphics Card
Xi-Fi Sound System Platinum

I tried unplugging the CPU Power, and the motherboard stayed on for more than 3 minutes, and didn't shut down, so I don't think it's a bad board. I unplugged one of the memory sticks, but I don't think it's that either, because when I had both in, and was able to access the settings for a few minutes, it registered the memory as being 2,048MB's with 2,047 free.

I unplugged the Hard Drive, DVD.....Not it. It goes to 'hard disk not found' error and then still shuts down after 30 minutes. When I unplug the Power Fan, it gives me a 'warning, voltage, hardware, or thermal problem, please check setup....'

So I'm thinking I applied the thermal paste wrong. I applied it according to the directions on the arctic silver website, and applied a small vertical line down the center of the CPU, where as last time I was told to only apply a small dot of the stuff the size of a rice grain. Could that be the problem?

When I have my old hard drive in, it also got as foar as the Windows xP logon screen, and then shut down after thirty seconds, so I'm thinking this could be the problem. I'm using the Stock Intel Heatsink fan too.
 
sounds like an overheat problem to me. I would clean your heatsink and reapply the paste. I was also told to use a small amount and not use a large glob, using a lot can definately cause more heat than if you apply a little.
 
Might be heat...

Could also be a power switch problem. Try jumping the board with a screwdriver, rather than using the switch.

Check your idle temps in the BIOS.
 
It's definetly the heat.

I reaplied the thermal paste twice, and it stayed on for a good five minutes. could adding another fan in there solve the problem? I have place for a 92 MM fan. but I don't know if I am applying the thermal paste wrong, or if another fan would solve it...

Edit - The Idle temp stayed at 65 Degrees for a minute, then it idled at 70-69 degrees back and forth... then it started climbing slowly after 4 minutes and shut off around 90 degrees.
 
It sound's stupid, but make sure you don't have the heatsink rotated 90 degrees. Had a guy here that did that and it'd shut down just as you got into setup.
 
What do you mean rotated? Should the Intel Logo be facing you a certain way? I.E. Intel readable (Downwards), Top of the word intel Facing Right, top of the word intel facing left, Top of the word intel facing down toward the PCI slots?

could that really make a differenace?

If not, maybe I should pick up a Zalman...because it is definetly the CPU heat that is causing it to shut down..
 
Sounds like the CPU HSF isnt properly installed. Double check it... it shouldnt be loose at all.
 
It works :).

I bit the bullet and got a Zallman. Now I owe 20$'s to the parents, as this thing just about maxed me out after buying all the other parts.... but it lives :).

I was a tad bit worried about installing the Zalman with all the preasure applied, a screw from the bracket popping loose and going across the room....but once I figured out that I could install it out of the case and then apply the bracket to the board I could apply it with a bit less preasure.

I don't notice too much of a speed increase going from an Athalon 64 3500 and 1024 MB of Ram to a duo Core 2.4 GHZ chip with 2 GB PNY DDR 2 memory......but it's great I can now watch HD movies on this sucker :). I just have to save up for the program to play said movies :).
 
Back
Top