Is my board pooched?

bishop7

n00b
Joined
Jun 12, 2004
Messages
19
(reposted from AMD mobo section, sorry about that)

Hello,

I recently bought an Athlon XP 2500 mobile. I tried using the socket mod to force it to autodetect it as a 200 MHz FSB part (http://www.ocinside.de/go_e.html?/h...amd_pinmod.html , check the 200 Mhz FSB to see where I put the U-shaped wires in the socket), but backed off on it and I think I ruined my socket somehow (though i'm not entirely sure) I see the indicator led is turned on, so the board IS getting power, but with the mobile CPU in the socket it will not turn on (I don't mean it just won't POST, it just won't turn on PERIOD)

I tried using the previous CPU (a TBred-B 2400+) in the socket with the same result. Funny enough, if I remove the CPU and turn on the power it powers on fine (or at least for a board wihout a CPU!)

Do any of you MB experts know what is wrong? My GUESS is that a fragment of the wire I used to bridge the pins is stuck in the socket and when the CPU is inserted it pushes it into a position which shorts out the board. More importantly, is there anything I can do to save this board?
 
Have you tried clearing out the cmos since? Maybe since it tried to boot at 200fsb X whatever multi, it was too much of a jump to run at its stock voltage, even unstable, so it just refused to post. Try that out, see what happens.

-K
 
Kako said:
Have you tried clearing out the cmos since? Maybe since it tried to boot at 200fsb X whatever multi, it was too much of a jump to run at its stock voltage, even unstable, so it just refused to post. Try that out, see what happens.

Actually, it doesn't even try to POST. The system does not turn on at all (even though the board has power) None of the other components attached to the board power on (like the cold cathode's, for example) unless there is no CPU in the socket. I have tried this with two different CPU's (the other CPU is a 2400+ which is able to run at 206 MHz FSB/2.472 GHz FSB at 1.8v and can POST at 200 MHz FSB at stock voltage.
 
Wierd, Could this be a result of the 4 ping connector not attatched to the mobo?

-K
 
Kako said:
Wierd, Could this be a result of the 4 ping connector not attatched to the mobo?

Actually, it's an nForce 2 board. For some reason, my sig isn't showing up. Sorry about that.

Detailed specs: Tested CPU's: Athlon XP 2500+ Mobile, Athlon XP 2400+
MB: A7N8X Deluxe
RAM: OCZ PC3200-EL (512 MB)
Radeon 9800 Pro 128m
WD Caviar SE 80 GB
Enermax 460W PSU
 
Oops. Guess my sig was showing up ... there is no 4-pin connector on the board, only the ATX connector.
 
Both my nforce 2 boards require it to be plugged in, in order to post at all. Thought maybe yours was same scenario. Any luck at all?

-K
 
No luck yet. I got a suggestion from the amdmb forums ... going to clear the CMOS while the PSU is unplugged from the mainboard and leave it for a little while. I don't think it will help, but i'm willing to try anything at this point.
 
Well, I cleared the CMOS, left the PSU unplugged from the board overnight ... didn't affect anything. The system still doesn't turn on ...
 
Have you checked the cpu's in a differant machine? If not, it may be a couple of bad procs from the motherboard. If you have, and they work fine, the board may be hosed.

If everything is installed, and connected properly, it sounds like a bad board.
 
Not really, but the processors were working before and I don't have an extra AMD machine to test them in anyway. I sincerely hope the processors aren't dead because of this. In either case I would need a new board anyway.
 
I fixed the problem. Apparently the Exos power switch splitter cable wasn't attached all the way (or the power lead attached to the control board was no longer feeding it enough power) so it works now.

/me <-- dumbass
 
Back
Top