Installed different video card and the computer would not BOOT..?

NewShockerGuy

Gawd
2FA
Joined
Jan 24, 2002
Messages
689
So I found out that my antec psu was dieing on my 2.53 rig... I got a new PSU, and I swapped that out.. tested A OK! I decided to put in a x850 card to replace the 9700 pro that was in my computer... Installed, turned on and I could hear EVERYTHING actually turn on my my HD led light wasn't flickering... So I kept shutting the computer off and on then finally it came on, I got into windows and installed new drivers..etc Restarted perfectly fine..

Today I go to turn the computer on and it DOES turn on but nothing on the screen... I can hear the hard drive spin up but that is it... I think the video card was taking too much power away from the HD? I switch rails and still had the same problem..

The PSU is a antec HE 500watt...

So then I hooked up a separate PSU into the x850 and turned it on while I turned my computuer one... I guess it didn't like that too much cause then it just beeped... Plugged it back into the HE 500 watt psu, turned the computer on and it just beeped...

So now I am running the stock 9700pro card....

I just wanted a small upgrade and it seems like it's not even going to work... is it because the card is capable of 8x but since the board only supports 4x agp that is the problem... or it's sucking too much power..?

This is weird..

Thanks,
-Nigel
 
I don't know how the AGP version of the X850 is, but on the PCI-E versions, you had to connect the PCI-E power connector to it in order for it to start up. You might have to connect the card to a molex connector.

Edit: Well here is a picture of the card:



I drew were you should connect the molex to the card. Make sure that when you plug it in, that no other devices are on the same line.
 
igl00jx said:
I don't know how the AGP version of the X850 is, but on the PCI-E versions, you had to connect the PCI-E power connector to it in order for it to start up. You might have to connect the card to a molex connector.


Yeppers, I did..

I had the 12v mollex connected to it... but I had to continue to turn on and off the computer, THEN finally it got into windows, installed the drivers perfectly fine...
Then after I shut it down and turned it back on a day later it was doing the same thing... like the hard drive just wasn't kicking over because the vid card was taking too much power..? So I used another psu JUST to hook into the vid card.. turned that on, then turned my computer on... I thought I smelled something funny on the vid card and then it started to just beep...

So as of right now it's the 9700pro..

This is bad, if I can't upgrade my computer a little pit...arg!

-Nigel
 
Make sure your card is completely seated in teh slot. I had that problem with my X1900 at first, but when I got to investigating I notice a little bit too much gold at the slot, So I took the card out and re inserted it and badda bing it worked.

Just noticed that you said you used a second PSU to power the Vid card, if the ground from both PSU weren't tied together then you MAY have smoke the card, due different ground references.
 
Would you happen to have another PC to test the card in? If not, a friend's?
 
ryan_975 said:
Make sure your card is completely seated in teh slot. I had that problem with my X1900 at first, but when I got to investigating I notice a little bit too much gold at the slot, So I took the card out and re inserted it and badda bing it worked.

Just noticed that you said you used a second PSU to power the Vid card, if the ground from both PSU weren't tied together then you MAY have smoke the card, due different ground references.


Welp I am almost 100% positive I fried the x850 by doing so...lol :-(

SOOOOOOOO................... I'm out that card...

But what I REALLY want to know is why the computer wouldn't boot.. I unfortuatanly don't have another computer that takes AGP... the only other computers I have are all PCI-E...

I do only have two rails coming from the PSU... since it's modular... I can get another rail to plug into it from work but do you think that is what could have caused it to not boot completely? I had one rail going to my ultraMRII, audigy, matrix orbital, then the other rail going into the HD, video card, and bulgin switch...

Do you think it would have even mattered just running a third rail and only having the vid card plugged into that one?

Thanks,
-Nigel
 
I had this issue with my 7800gs oc.... I found that i had to hook up a different 12volt molex to it cause the first one was also feeding a few other devices... See if you can arrange your molex plugs so that you have one spare thats not feeding power to anything else. I think these are called rails. Power being drawn way from the molex for your video card could cause the video card to not boot cause it's not getting the nessicary power to it.
 
Conano said:
I had this issue with my 7800gs oc.... I found that i had to hook up a different 12volt molex to it cause the first one was also feeding a few other devices... See if you can arrange your molex plugs so that you have one spare thats not feeding power to anything else. I think these are called rails. Power being drawn way from the molex for your video card could cause the video card to not boot cause it's not getting the nessicary power to it.

No, rails are completely different sources that are regulated separetly from each other. Most (not all) PSU have all the molex connections on the same 12v rail, even though they're on separate wires, they go back to the same spot on the PSU's pcb.
 
ahh ok, thanks for the clarification. All i know is i used a molex plug that wasnt running anything else as well, so power wasnt being drawn away from the video card, and it worked.
 
Back
Top