IC7 Overclock question

Operaghost

[H]ard|Gawd
Joined
Jun 4, 2004
Messages
1,315
I'm buying an Abit IC7, gonna put it up with a 2.4c

My question is how exactly does the CPU frequency get overclocked since you can't change the multiplier?
Just from increasing the FSB speed?
I'd like some responses from some experienced IC7 users, on what are some of thier more successful OC settings, including what memory they have etc.

Thanks in advance
 
Operaghost said:
I'm buying an Abit IC7, gonna put it up with a 2.4c

My question is how exactly does the CPU frequency get overclocked since you can't change the multiplier?
Just from increasing the FSB speed?
I'd like some responses from some experienced IC7 users, on what are some of thier more successful OC settings, including what memory they have etc.

Thanks in advance

Hey, I got teh IC7-G:

Just raise teh fsb untill you cant anymore, then change the fsb/mem ratio to 5/4 and raise teh clock speed some more.

If its not to stable, raise teh memory voltage and lower teh mem timeings
 
Operaghost said:
I'm buying an Abit IC7, gonna put it up with a 2.4c

My question is how exactly does the CPU frequency get overclocked since you can't change the multiplier?
Just from increasing the FSB speed?
I'd like some responses from some experienced IC7 users, on what are some of thier more successful OC settings, including what memory they have etc.

Thanks in advance

My FSB can not go any further than 258MHz with stability even I set the VCore to 1.6V and the VDDR to 2.65V. I can run @ 260 if I put some ice into my water reservoir. I think the problem origins from my bad radiator and the hot mosfet on the mobo. Does anyone have some xp when ocing with IC7 with HT Northwood, can you show me?
 
The IC7 undervolts the memory unless you mod it. Set the DDR voltage to 2.8 with impunity.
 
LstOfTheBrunnenG said:
The IC7 undervolts the memory unless you mod it. Set the DDR voltage to 2.8 with impunity.

Does this apply for the IC7-G too?
 
take your multiplier, times your front side bus speed and you have your cpu speed.

12 X 200 = 2400mhz
12 x 209 = 2500mhz
12 x 217 = 2600mhz
12 x 225 = 2700mhz
12 x 233 = 2800mhz
12 x 242 = 2900mhz
12 x 250 = 3000mhz ( 25% overclock )
12 x 258 = 3100mhz
12 x 266 = 3200mhz ( 33% overclock )
12 x 275 = 3300mhz
12 x 284 = 3400mhz
12 x 292 = 3500mhz
12 x 300 = 3600mhz ( 50% overclock )
 
Demonfire said:
Does this apply for the IC7-G too?

The IC7, The IC7-G, The IC7-G Max II, and the IC7-G Max III are all affected by this issue as far as I know
 
LstOfTheBrunnenG said:
The IC7, The IC7-G, The IC7-G Max II, and the IC7-G Max III are all affected by this issue as far as I know

i have my vdimm set to 2.8 and i see it as only 2.78.
 
A new question 'bout my system has just been comin'. Please help.

At first, I raised my FSB to 220 (~ 2.6GHz) with all volt @ DF, my RAM did also get to 220MHz (CPU:RAM ratio is 1:1). That means my RAM may run fine @ 220MHz with V-DDR @ DF.

Next time, I raise CPU's FSB to 250 and let it run 5:4 with the memory (@ 200MHz). Later, I push FSB a lil' bit more which is 258MHz (still 5:4 with memory) (all volts are @ DF). Then, I push the FSB to 260 then it can not run stable. (VCore: 1.575V. V-DDR: 2.65V) unless I put some ice into my water reservoir.

So I think the problem is my CPU not my RAM. Am I right? Can anyone tell me what should I do to push my FSB further? Increasing the voltage seems to not help or should I push some more VCore?
 
few things to try...

when i first got my ic7-g it had a really old bios revision on it somewheres around 15 and the cpu was overclocking for shit, wouldnt even stay stable at 3.0. as soon as i upgraded to the lastest bios (bios 22 at the time) i immediatly was able to run at 3.3 stable. so try upgrading your bios to the latest if you havent done that allready. to eliminate memory as the problem, set the divider to 3/2 and max out the latency's to 3-4-4-8.

if niether of those work, its very possible that you have a 2.4 that doesnt overclock well, its not unheard of. all cpu's are not created equally.
 
acascianelli said:
...its very possible that you have a 2.4 that doesnt overclock well, its not unheard of. all cpu's are not created equally.

My IC7 is using BIOS 24 already. I think the problem is from my CPU.
 
do you have the pci/agp speed locked at 33/66? that would cause instability also. and set the game accelerator to auto if you use it on any setting.
 
Locking PCI/AGP up is da 1st thing I do when OCin'. Let me check the Game Accelerator features. However, I think it is @ Auto default.
 
Back
Top