I just overclocked my Core i7 920 to 3.8GHz and would like some feedback to see if my settings are OK. The only thing I am worried about is the temps which are varily high for idle and load. Keep in mind, my ambient room temperature is 81F. Idle is mid to high 40s and with the LinX test I did (20 passes at 25000 problem size), my load temps were 80/77/77/75 with a VREG temp of 81F.
Mother Board ( EVGA X58 SLI )
CPU ( i7 920 )
CPU Cooler ( Prolimatech Megahalem )
Memory ( Mushkin Blackline DDR3-1600 )
PSU ( Corsair TX850)
GPU ( GTX480 x2 )
Frequency Control
CPU Clock Ratio ( 20X )
CPU Host Frequency (Mhz) ( 190 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) ( 3045MHz/16X )
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )
Memory Feature
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1522MHz/ 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way)
Memory Low Gap ( Auto )
tCL Setting ( 9 )
tRCD Setting ( 9 )
tRP Setting ( 9 )
tRAS Setting ( 24 )
tRFC Setting ( 110 )
Command Rate ( 1T )
Voltage Control ( With VDroop)
CPU VCore ( 1.23125)
CPU VTT Voltage ( +200 )
CPU PLL VCore ( 1.65 )
**IOH PLL VCore ( 1.5 )
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( 1.2V )
IOH VCore ( 1.1V )
IOH/ICH I/O Voltage ( Auto/ 1.1V )
ICH VCore ( 1.125 )
*PWM Frequency ( Auto/800 KHz )
Hyperthreading Enabled
I am pretty sure I will need to adjust some things but not sure what to get my temps down.
Mother Board ( EVGA X58 SLI )
CPU ( i7 920 )
CPU Cooler ( Prolimatech Megahalem )
Memory ( Mushkin Blackline DDR3-1600 )
PSU ( Corsair TX850)
GPU ( GTX480 x2 )
Frequency Control
CPU Clock Ratio ( 20X )
CPU Host Frequency (Mhz) ( 190 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) ( 3045MHz/16X )
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 100 )
Memory Feature
Memory Speed ( Standard )
Memory Control Setting ( Enabled )
Memory Frequency ( 1522MHz/ 2:8 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way)
Memory Low Gap ( Auto )
tCL Setting ( 9 )
tRCD Setting ( 9 )
tRP Setting ( 9 )
tRAS Setting ( 24 )
tRFC Setting ( 110 )
Command Rate ( 1T )
Voltage Control ( With VDroop)
CPU VCore ( 1.23125)
CPU VTT Voltage ( +200 )
CPU PLL VCore ( 1.65 )
**IOH PLL VCore ( 1.5 )
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( 1.2V )
IOH VCore ( 1.1V )
IOH/ICH I/O Voltage ( Auto/ 1.1V )
ICH VCore ( 1.125 )
*PWM Frequency ( Auto/800 KHz )
Hyperthreading Enabled
I am pretty sure I will need to adjust some things but not sure what to get my temps down.