HP Blackbird upgrade post build troubleshooting help

rinaldo00

2[H]4U
2FA
Joined
Mar 9, 2005
Messages
2,931
I decided to start a new thread because this has now gone from a request for build suggestions to build troubleshooting.

To summarize my situation for new readers and to remind old readers I am upgrading a HP Blackbird 002 Dedication edition computer. Since it is my first ever build, I decided to do it in steps. I kept my 2 NVIDIA Geforce 8800 Ultras for now. Since I live in Chicago and I wanted to finally get started I went to Microcenter and bought everything there. Luckily they had GREAT prices! Here is what I started with.

$310 - Core i5-2500k and MSI P67A-GD65
$50 - Patriot Extreme Performance Sector 5 G Series 8GB DDR3-1333 (PC3-10666) Enhanced Latency Dual Channel Desktop Memory Kit (Two 4GB Memory Modules)
(no G.SKILL in stock and the tech guy highly recommended this so I gave it a shot)
$50 1 TB Toshiba HD (until my SSD arrives)
$88 - Windows 7 Home Premium 64-bit (open box/resealed)

For now I decided not to water cool the CPU so I just used the CPU fan it came with. The MB was VERY different from my ASUS Striker Supreme 680i, but I think I hooked up everything correctly. When it came time to connect my 2 DVD drives I was shocked that there was no IDE slot! Rather than swap out my cool slimline DVD drives I decided to drive back to Microcenter and buy a PCI to IDE card (hope that was a decent decision)

I closed everything up, powered up, and things worked! Got to the BIOS screen and looked around, then chose to load the optimial settings (as recommended in the manual) and booted off the Windows 7 CD. Here is were things went bad.

The Win7 install stopped with this error:

"A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVDm or USB flash drive, please insert it now. Note. If the windows installation media is in the drive, you can safely remove it for this step."

I tried using the CD that came with the PCI to IDE card but that didn't work. Looking online with my laptop I saw people claim that perhaps the DVD drives were too old, or their firmware needed to be updated. Since I knew those DVD drives worked with Vista I tried installing Vista but I got the same error.

By now I was extremely frustrated (and cursing Microsoft) and frustration leads to dumb impulses. I decided to put my old Vista OS HD in and try booting off of that. I figured with such a changed PC that Vista would not recognize it and give me some sort of error. To my UTTER amazement it worked! Not only that but it sensed all the new hardware and installed drivers for it all!

So, it looks like my hardware is installed correctly, but how do I install Win7 on my new drive? The only solution I read was to install off of a USB drive. Any other suggestions?

Thanks!
 
Sounds like the BIOS isn't recognizing the IDE controller card in the PCI slot. I would highly recommend spending the ~$20 on an SATA optical drive. They are super cheap and it will make things a LOT simpler.

I recommend this Samsung drive - SAMSUNG CD/DVD Burner - $18.98
 
Easy, use the ms utility to make your win7 dvd into a bootable pendrive (4gb plus) with your vista os drive. Put blank disk back in set bios to boot from usb. Install windows, let it pick up the driver online for your ide card, job's a goodun.
 
Thanks for the tips! You think once Win7 is installed the IDE card will work?
Or is tweaking the BIOS needed to recognize that PCI to IDE card? They make SATA to IDE cards too, with 8 SATA slots maybe I could do that. Or do I need a SATA DVD?
 
Thanks for the tips! You think once Win7 is installed the IDE card will work?
Or is tweaking the BIOS needed to recognize that PCI to IDE card? They make SATA to IDE cards too, with 8 SATA slots maybe I could do that. Or do I need a SATA DVD?

If it's working in vista, then chances are very high it should work without any problems.
It can also work if you load the drivers for the ide card with Windows 7, but a usb install is easier
 
Here is an update:
I am using a bytech pci express controller card that said it will do pci to ide. When I booted into Vista I saw that the DVD drives were NOT recognized. I used my laptop to copy the CD driver disk that came with the card to a USB drive. Plugging it I saw 5 directories. I choose to enter the PCIe directory because that is the slot I installed it in. Inside that were 3 directories
JMB36xg
MSC9901
Sil3132

Reading up on all 3 products it seemed the JMB36xg was what I needed. Here is what it does:

JMB363 is a single chip, one-lane PCI Express to two-port Serial ATA II and one-port PATA Host Controller. The JMB363 is designed to provide two-port SATA II and one-port PATA connectivity. The JMB363 supports both AHCI and Legacy IDE controller to increase system feasibility

It came with an install program, installed, rebooted and it worked.

Next step was to boot off the Win7 CD and when the driver request came up load the drivers. In the drivers directory were 2 directories:

amd64
x32

I tried x32first and didn't work, the amd64 DID work and let me continue to install Win7. I stopped there to see what people think, is the fact that the directory is called AMD is a problem, or do you think it really is just a generic 64 bit driver?

Keep in mind eventually I'll probably switch to SATA DVDs in the future, but this case requires slot loading drives.

Thanks again!
 
AMD developed the 64-bit system that Intel now uses. The more agnostic term is x86-64. But it's fine even though you're running Intel. Alternatively you could look into getting slimline SATA DVD drives and mounting the old faceplates on the new drives. Or SATA to IDE cards. But this should eventually work if you keep doing what you're doing.
 
Back
Top