How to set these things up? Alphcool + DDC

Joined
Jul 12, 2005
Messages
51
I have the following components, may experts here please give me advice on the best way to set these things up , thanks :D
Alphacool Nexxos XP cpu block
Alphacool Nexxos gpu x2
Alphacool Nexxos nb
Watercool Dual HDD block

DDC pump x2

Alphacool Nexxos radiator 12.3 (1pass) and 12.1 (2 pass) http://www.alphacool.de/upload//high/14111_1.jpg

5.25inch bay reservoir
http://www.alphacool.de/upload//high/15609_1.jpg

all the above components are G1/4, i am thinking of using 10mm ID tubing, i would like to use 3/8inch ID tubing (which is what i am using now) but it 12mm Quickfit dun seems to fit on the nexxos block :( i actually have another ALphacool AP1500 pump http://www.alphacool.de/perl/shop.p...menu_id=2&prod_id=130&art_kz=131&art_id=13106
but i think its better off to use 2xDDC with these restrictive nexxos blocks, right? lastly, i have 2 extra reservoirs too, not sure if i shall run dual loop or just one loop and running the pumps in serial. :confused:
 
wengchiochan said:
I have the following components, may experts here please give me advice on the best way to set these things up , thanks (would be nice if cathar can give me some advice too.

Alphacool Nexxos XP cpu block
Alphacool Nexxos gpu x2
Alphacool Nexxos nb
Watercool Dual HDD block

DDC pump x2

Alphacool Nexxos radiator 12.3 (1pass) and 12.1 (2 pass) http://www.alphacool.de/upload//high/14111_1.jpg

5.25inch bay reservoir
http://www.alphacool.de/upload//high/15609_1.jpg

all the above components are G1/4, i am thinking of using 10mm ID tubing, i would like to use 3/8inch ID tubing (which is what i am using now) but it 12mm Quickfit dun seems to fit on the nexxos block i actually have another ALphacool AP1500 pump http://www.alphacool.de/perl/shop.p...menu_id=2&prod_id=130&art_kz=131&art_id=13106
but i think its better off to use 2xDDC with these restrictive nexxos blocks, right? lastly, i have 2 extra reservoirs too, not sure if i shall run dual loop or just one loop and running the pumps in serial.

Well seeing as you have all those pumps I would run 2 or more loops. I have similar issues and I ran my 2 GPU's on one separate loop, my CPU on another separate loop, and am considering putting the NB and HD coolers on a third loop. :eek:

So how about this:

Loop 1

Res > Pump > Rad 12.3 > CPU > GPU x 2 >

*******************************************************

Loop 2

Res > Pump > Rad 12.1 > NB > HD >

You can use the same reservoir, but if you are going to do that you might just want to run them all in one loop. My suggestion is to run two different reservoirs. 10mm or 3/8" tubing will be fine.
 
wengchiochan said:
all the above components are G1/4, i am thinking of using 10mm ID tubing, i would like to use 3/8inch ID tubing (which is what i am using now) but it 12mm Quickfit dun seems to fit on the nexxos block

Well, as you said all blocks are threaded G1/4.If you want to use Plug&Cool ou Quickfit with a 12/10mm (OD/ID), you can try to obtain from Legris (www.legris.com) some LF3000 connectors that have the same thread G1/4 but use the 12/10mm tubing.
Remember that Tygon tubing is out of the question in this case, due to the thicker walls.
By the way to prevent the colapsing of the tubes you can also use ferrules (if you visit the legris web site its uner the tubing section in accessories), much like the John Guest fittings that Swiftech used.
 
So how about this:

Loop 1

Res > Pump > Rad 12.3 > CPU > GPU x 2 >

*******************************************************

Loop 2

Res > Pump > Rad 12.1 > NB > HD >

i was thinking of using 2loops too. but i am afraid that i will waste the powerful of the DDC on doing this. u see, the nexxos blocks are blocks with high pressure drop. so, for the 1st loop, the flow rate will be quite low due to the 3 restrictive blocks. for the 2nd loop, the flow rate will be too good since there is only one restrictive block and one non restrictive block with a small radiator. u see what i mean? (my english isn't very good :( ) i could be wrong though.
 
Jag said:
Well, as you said all blocks are threaded G1/4.If you want to use Plug&Cool ou Quickfit with a 12/10mm (OD/ID), you can try to obtain from Legris (www.legris.com) some LF3000 connectors that have the same thread G1/4 but use the 12/10mm tubing.
Remember that Tygon tubing is out of the question in this case, due to the thicker walls.
By the way to prevent the colapsing of the tubes you can also use ferrules (if you visit the legris web site its uner the tubing section in accessories), much like the John Guest fittings that Swiftech used.

i wanna use legris quickfit with 12/10mm as well, i know they will fit very well on all of the nexxos blocks except the nb block i guess. the nexxos nb block is very small, the distance between the 2 thread is very small. i really wanna use 12mm OD qf but it seems the problem i have here is mainly on the nb block. its also nice to use 12/10mm hose because it will just fit perfrectly for my DDCs.

anyway, do u guys think it is not a good solution of to run these stuff in one loop?
 
Jag said:
Well, as you said all blocks are threaded G1/4.If you want to use Plug&Cool ou Quickfit with a 12/10mm (OD/ID), you can try to obtain from Legris (www.legris.com) some LF3000 connectors that have the same thread G1/4 but use the 12/10mm tubing.
Remember that Tygon tubing is out of the question in this case, due to the thicker walls.
By the way to prevent the colapsing of the tubes you can also use ferrules (if you visit the legris web site its uner the tubing section in accessories), much like the John Guest fittings that Swiftech used.

by the way, i just called the legris distributors in brisbane for price enquires, and they are DAMN EXPENSIVE!!! it costs us$9 for an elbow 12mm qf!! :mad:
thats double the price that i can get from alphacool :eek:
 
wengchiochan said:
by the way, i just called the legris distributors in brisbane for price enquires, and they are DAMN EXPENSIVE!!! it costs us$9 for an elbow 12mm qf!! :mad:
thats double the price that i can get from alphacool :eek:

Same here in the USA :( Legris distributors are high priced everywhere except from the OEM's. But you figure they buy bulk fittings probably 250+ of each size at a whack so they get rock bottom pricing. The AC dealer here in the states says he sells them for what he can buy them here. ;)
 
Have u heard of Metalwork fittings? they are as good as legris and are very expensive in australia too. but i just called a friend of mine in hong kong and they are super cheap over there! and they have qf fit size from 8mm OD to 14mm OD G1/4!! (www.metalwork.it)
so i can even use the D5 on a german style watercooling system! wow! :D

and u can't believe how cheap they are. for a straight 12mm qf, it only cost us$1.7! they are imported from europe to hk too....looks like the aus and us distributors are really make hell lots of profits.

looks like i will can consider purchasing a D5 for my watercooling system in the future. the only problem i have if i use 1/2 tubing will be the hose kincking problem in the gpu1 gpu2 and nb area and there isn't really much space around there for big hoses... :(
 
Well...how about splitting 1/2" to two 3/8" lines to go through the GPU's and Y them back into 1/2" line?
 
Top Nurse said:
Well...how about splitting 1/2" to two 3/8" lines to go through the GPU's and Y them back into 1/2" line?

will i lose a lot of flow by doing that? as i heard that D5 only works well in 1/2 loops.
 
Back
Top