How do you apply thermal paste on heatspreader?

Aelfgeft

2[H]4U
Joined
Jun 8, 2005
Messages
2,343
The last time I built a computer was in the beginning XP days, and I never messed with Pentium 4s. So, I'm only familiar with the old credit card spreading over the tiny core bit.

With an Athlon 64, how do you now apply the thermal paste to the CPU and HS? And is there anything special you do when you install it? Burn in tips?

Edit: These questions are being directed to the overclockers. I've been to AMD's, ArcticSilver's, and ThermalRight's websites. Don't refer me there. I want to know how YOU guys do it. ;)
 
Akuma said:
Dab in middle and let the heatsink spread it.
this is not a good idea because you end up with pockets of air..it is best to spread it yourself.

If you don't believe me...put some peanut butter on a plate...press down on it with another plate..lift it up and see how it tends to spread out on some areas but not others....now spread out the peanut butter on the plate, put another plate on it...and it works nicely :)
 
Okay...how would you spread it? Would a credit card's edge really do the job? How much pressure would you apply? I've seen the AS website suggest a baggie over your finger. What have you all used?
 
I always used a razor blade to spread AS5 on the heat spreader on my P4 systems. Works like a charm.
 
Steeeeve said:
this is not a good idea because you end up with pockets of air..it is best to spread it yourself.

If you don't believe me...put some peanut butter on a plate...press down on it with another plate..lift it up and see how it tends to spread out on some areas but not others....now spread out the peanut butter on the plate, put another plate on it...and it works nicely :)
Actually, if you spread it all out you are much more likely to get air pockets since you are just lightly moving it about rather than putting pounds of pressure on it with the heatsink.
 
pressure has got nothing to do with it...you just need an even spread..not too thick...over the chip.

A razor blade works well.
 
Hmmm, if you read the instructions ( Found here ) It dose say, best results when you dab it in the middle. With a CPU with heat spreader, you don’t really want the entire thing covered in AS. let the pressure form the HS spread it where it needs to go. Unless you lap the Heat spreader, then maybe you might want to apply it with a razorblade to the entire surface.


edit: ownd
 
hey, i'm not gonna argue anymore...do it the way you want...just from personal experience I find it better to spread it yourself
 
I(illa Bee said:
Hmmm, if you read the instructions ( Found here ) It dose say, best results when you dab it in the middle. With a CPU with heat spreader, you don’t really want the entire thing covered in AS. let the pressure form the HS spread it where it needs to go. Unless you lap the Heat spreader, then maybe you might want to apply it with a razorblade to the entire surface.


edit: ownd

Read above edit. :p

Besides which, I wouldn't listen to AS's instructions without a grain of salt since it wouldn't be unreasonable to assume they want to sell a lot of their stuff ;)
 
"Our testing has shown that this method minimizes the possibility of air bubbles and voids in the thermal interface between the heat spreader and the heatsink. Since the vast majority of the heat from the core travels directly through the heat spreader, it is more important to have a good interface directly above the actual CPU core than it is to have the heat spreader covered with compound from corner to corner."

besides, what the people who make AS say, in my own experence, I have gotten 2-3 degrees C better temps doing it there way over covering the entire Heat Spreader... Also AS5 is too expensive to be wasteing it on the entire heat spreader
 
I've tried it both ways and found following the AS's instruction to be best. My temps were roughly 5 degrees C higher when I spread the paste myself.
 
Aelfgeft said:
Read above edit. :p

Besides which, I wouldn't listen to AS's instructions without a grain of salt since it wouldn't be unreasonable to assume they want to sell a lot of their stuff ;)

i generally follow artic silver's directions when applying it, but you might also consider that their method is simply less error-prone, which is alot more valuable in terms of increased customer satisfaction than slightly better performance.

that said, i get very consistant results with artic silver's application method, which seems to suggest it's working at peak efficiency, rather than consistantly low efficiency due to a similar amount of air bubbles beingh introduced with each consecutive application.
 
Back
Top