Help with New PC and Possibly slow drive

kenju4u

n00b
Joined
Jan 20, 2010
Messages
14
Hi guys,

I have a Asus P6T SE Mobo/i7 920 processor, with WD5000AAKS 500 Gig drive running on Windows 7 64bit and I am getting 101 MB/sec Average speed. I was initially running on IDE in the BIOS and i've updated that to AHCI. Ran the HD Tune test again and dont see any change in hard drive speed. My questions is that shouldnt it be closer to 300MB/sec since its a SATA 2 drive. Why is my drive so slow? Would really appriciate some help since this is a 1 week old PC and I feel the hard drive issue is really causing my PC to be not performing as it should.

Here is some more info from HD Tune:

HD Tune Pro: WDC WD5000AAKS-00V1A0 Information

Firmware version : 05.01D05
Serial number : WD-WMAWF1291062
Capacity : 500.1 gB (465.8 GB)
Buffer size : 16384 KB
Sector size : 512 bytes
Standard : ATA8-ACS - SATA II
Supported mode : UDMA Mode 6
Current mode : UDMA Mode 7
Avergae speed : 101 MB/s
Rotation speed : -

S.M.A.R.T : yes
48-bit Address : yes
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Firmware Upgradable : yes
Automatic Acoustic Management: yes
Power Management : yes
Advanced Power Management : no
Interface Power Management : yes
Power-up in Standby : yes
Security Mode : yes
Native Command Queuing (NCQ) : yes

Volume :
Capacity :
Free :
Usage :
File system :
Serial :

Volume : Windows (C:)
Capacity : 476837 MB
Free : 396596 MB
Usage : 17%
File system : NTFS
Serial : 8811-7E8D



- Ken
 
100Mb/s is right where you should be for a modern spindle (disk) 7,200 rpm hard drive.

300Mb/s is the theoretical max for that standard, which not even the fastest Solid State Drives (SSD) can hit. Good (EXPENSIVE) SSD's usually get around 250mb/s read & 100Mb/s write.
 
Ok thanks for the info its good to know that atleast its not broken. I was wondering what this means then:

Standard : ATA8-ACS - SATA II
Supported mode : UDMA Mode 6
Current mode : UDMA Mode 7 <----- Is this running on SATA 2?
 
Yes those are good numbers.

You want faster? Get another one or two drives and run RAID 0 ;)

Your board and system should support it with ease
 
Ok then why does it say i am in UDMA Mode 7 when I should be in ATA8 SATA II?
 
your benchmarks are fine, don't worry about the exact wording of what some program / app says. As long as your performance is fine.
 
I updated the Intel Storage Matrix Manager to 8.9 since the windows 7 64bit one was really old from 2006.

Here is the data again:

HD Tune Pro: WDC WD5000AAKS-00V1A Information

Firmware version : 05.01D05
Serial number : WD-WMAWF1291062
Capacity : 500.1 gB (465.8 GB)
Buffer size : 16384 KB
Sector size : 512 bytes
Standard : ATA8-ACS - SATA II
Supported mode : UDMA Mode 6
Current mode : UDMA Mode 6
Avergae speed : 101 MB/s
Rotation speed : -

S.M.A.R.T : yes
48-bit Address : yes
Read Look-Ahead : yes
Write Cache : yes
Host Protected Area : yes
Device Configuration Overlay : yes
Firmware Upgradable : yes
Automatic Acoustic Management: yes
Power Management : yes
Advanced Power Management : no
Interface Power Management : yes
Power-up in Standby : yes
Security Mode : yes
Native Command Queuing (NCQ) : yes

Volume :
Capacity :
Free :
Usage :
File system :
Serial :

Volume : Windows (C:)
Capacity : 476837 MB
Free : 396411 MB
Usage : 17%
File system : NTFS
Serial : 8811-7E8D




HD Tune Pro: WDC WD5000AAKS-00V1A Benchmark

Test capacity: full

Read transfer rate
Transfer Rate Minimum : 24.0 MB/s
Transfer Rate Maximum : 130.9 MB/s
Transfer Rate Average : 99.2 MB/s
Access Time : 15.8 ms
Burst Rate : 175.4 MB/s
CPU Usage : -1.0%
 
Back
Top