Help with E6300 and GA-945P-S3

Joined
Jan 8, 2006
Messages
37
What do I need to do to oc my E6300 on my mobo. Do you guys know any good sites for tutorials and how high do you think I can oc with stock cooling.
 
You can search for my "beginners conroe overclock guide" or something... It's good for the P965 based boards.

It's quite general, so... Don't expect a great walkthrough, but it gets you through most of the settings in a short amount of time. you can always IM me over MSN too (email in profile).
 
yeah. OCing isn't rocket science, I don't understand you people who worry about it. On Intel mainboards, all you gotta watch for is that your ram isn't being clocked through the roof.

I'm not familiar with that particular board, but I'm assuming that it has phoenix award BIOS.

couple terms to understand (just covering all the bases)
- FSB (Front side bus): the bus between the North bridge and South bridge, measured in MT/s (aka MHz effective)
- Bus speed (sometimes called core FSB): This is the number all bridge and CPU speeds are based on. Bus speed x 4 = total FSB speed. Bus speed x CPU multiplier = total CPU speed.
- North bridge: the chip under the heat sink on the motherboard, also the controller of your memory. it links everything to the CPU

1: set your RAM:FSB to 1:1 (BIOS --> advanced chipset features --> FSB and RAM settings)
2: change your CPU voltage to whichever you'd like. To stay safe, on a C2D, keep it below 1.50V. It's rational, in that the more you over volt, the shorter the lifespan of your CPU. That simple. All CPUs (including ones at stock voltage) will eventually die from electron migration.
3: start raising the Bus Speed or FSB speed. Depending on your version of BIOS, it may give only one of these options, or both, either way, its a direct relationship. Remember raising your bus speed by one increases FSB speed by 4. On that motherboard, you can prob obtain 400MHz bus speed, so don't go up 1MHz... by 1Mhz... by 1MHz. take some big steps.
4: eventually your system will fail to post. If this happens, i believe the all Gigabyte DS's have a failsafe, and that if you give it enough time it will restart on stock or last known good settings. When this happens, change to the settings you knew that it started at well. If this does not happen, and it fails to post and does NOT revert to any postable settings, your going to have to do it old-school. take off the side panel, find the CMOS battery (a little silver disk usually has lettering around the outside, cant miss it, its about the diameter of a penny, and the thickness of... a stack of three pennies (lol)). there are a couple different mechanisms to pop it out, sometimes all you have to do is push it, sometimes theres a clip, either way its completely safe. if you cant figure out how to get it out, the manual will tell you. after you take it out, wait for 30 secs, with CMOS battery not in the motherboard, and with all power off. This will reset CMOS, and your computer will next post at stock settings.
5: set ram speed closest to stock. this can be the biggest pain in the ass of your overclock. If your motherboard only has the options of 1:1, 3:2, and 5:4, you might have a hard time finding a good setting for your ram. BIOS calls this RAM : FSB, it is actually RAM : Bus Speed. anywho, take your bus speed, multiply by the larger number, and devide by the smaller number, thats your total ram speed. so, if i select 3:2 and have a bus speed of 450MHz, my ram speed is 450 x 3 / 2, or 675MHz. 680i does not actually have an unlinked overclock for ram, what it does have, is really really precise ratios. EX if you tell your ram to run at 605MHz, and your bus speed is 450MHz, it will find the closes ratio it can come up with. In this situation it would be something like 12:9... This is my theory anyways, cuz it never gives me the exact MHz i want when i use the unlinked mode.
6: use the ratios and try to overclock your ram using the above info. IMHO, the best way to go is to find the highest MHz possible, then start worrying about timings. some may say difference.
7: ram timings. lower these as much as possible. CAS is generally considered the one that has the biggest impact on performance, as such you can usually get it in .5 clock increments.
8 (optional): you might tryy to overclock your PCIe lanes, but they generally have little impact on performance, and CAN totally screw over your graphics card. Link boost is a setting that runs the PCI-e lanes at 125MHz (stock is 100MHz). This can damage your graphics card and offers little performance increase, I'm not doing this, if you are, do reasearch.

You might consider repeating step one, often once a CPU settles in at its voltage, it will give up a few more MHz.
 
I successfully overclocked to 2.45 but that is the only speed I can reach. If I try to clock any higher it goes back to 1.86. Any ideas why?
 
Back
Top