Help! DS3 300mhz fsb max - whats wrong?

GrumpBob

n00b
Joined
Sep 27, 2006
Messages
42
After weeks of reading reviews I just completed my DS3 build.

Specs:
E6400
DS3 mobo (flashed to F7 bios)
2GB Corsair xms2 pc6400 ram
Thermaltake big typhoon cooler with AS5
evga 7900gto video

vcore = 1.387
mch = +.1
fsb = +.1
ram = 5-5-5-12
temp = 42C (which seems high to me)

I can't get past 300 mhz fsb! At 325 the board reboots at startup.

1. When I loaded the gigabyte drivers, I did them one at a time (I didn't load the raid drivers). When I got to the last USB driver it kept cycling the install over and over again.
The final USB driver check box never grays out to show that it installed.

2. CPUZ shows that I am running the F4 bios - yet the boot screen says F7?

3. XP is running like a dog. IT takes CPUZ 20+ seconds to load. Every application takes forever to display. Coming from a 3ghz P4, I didn't expect a radical increase in XP perfomance, but I sure don't expect a noticible decline.

I suspect a bad mobo. I hate to send it back and find out that it's the ram.

Any suggestions
 
Update your bios. with the fo2 or f03 (I *think), the ds3 absolute screams, people get close to 400.
 
use @bios to flash instead of a flash with a floppy or something, might help
 
Maybe the board and chip just won't go over 300?? How do things run at stock?? My DS3 won't go over 400 no matter what I do...but I'm using 667 ram, so I am already overclocking it to 800....but I am doing it with relatively tight timings...4-4-4-12.
 
Are you ocing with virtialization, and EIST fuctions enabled, if so disabled them.
 
Has anyone seen CPUZ report a different Bios then what the board reports?
It's odd that the initial bios was F4 and thats what CPUZ shows.
 
cpuz reports F4 for my DS3, but it is definately running F7. There are changes to the BIOS that you CAN'T miss when upgrading to F7.

And BTW, people are reaching 500Mhz FSB with that board. Mine is currently at 450 and when my Infinity cooler gets here, it will go higher. So as long as your DS3 is functioning fine, you can expect MUCH higher FSB with the right components. Good luck!
 
So, everyone agrees that I should get higher overclocks. Does anyone have any idea why I'm not. From what I've read I should be able to get to 400 without any tweaks.

Could my ram be at fault?
 
GrumpBob said:
So, everyone agrees that I should get higher overclocks. Does anyone have any idea why I'm not. From what I've read I should be able to get to 400 without any tweaks.

Could my ram be at fault?
Did you read my above post :confused:
 
Newls1
Yes I did read your post. Unfortunately both those settings were already disabled.
If I go past 325, the machine reboots 4 times and the bios is reset to default.
 
Damn it man, the DS3 is a really good board, so dont 2nd question the reason you got it! You will find out why, then smack yourself cause it was so easy.
 
Hmm I agree about DS3 should be getting at least 400 easy. Btw you set the ram divider to 2 right ? When you set FSB 300, what is the posted speed ?

The XP should be snappy, a least that's what I feel with my system. And the temp according core temp is somewhere in 55C full load, ambient is 25ish.

We got similar system, except I flashed back to F6, using @BIOS in windows, and don't forget to set it back to stock speed before flashing. So reflashing would be good idea, and finish install XP before any overclocking. Then if you suspect the memory is not good, run memtest at stock speed. You have to make sure stock speed is perfect if you want to find out the problem.

Also disable stuff you don't need at bios, and that CPU voltage is already too much for 300FSB. In fact you should increase CPU voltage only when you didn't pass stability test, then you can find the least voltage for your setup.
 
whiskey29 said:
Hmm I agree about DS3 should be getting at least 400 easy. Btw you set the ram divider to 2 right ? When you set FSB 300, what is the posted speed ?

The XP should be snappy, a least that's what I feel with my system. And the temp according core temp is somewhere in 55C full load, ambient is 25ish.

We got similar system, except I flashed back to F6, using @BIOS in windows, and don't forget to set it back to stock speed before flashing. So reflashing would be good idea, and finish install XP before any overclocking. Then if you suspect the memory is not good, run memtest at stock speed. You have to make sure stock speed is perfect if you want to find out the problem.

Also disable stuff you don't need at bios, and that CPU voltage is already too much for 300FSB. In fact you should increase CPU voltage only when you didn't pass stability test, then you can find the least voltage for your setup.

Alright, I have to plead ignorance on this one. What ram divider? No I didn't set it to 2.
 
So you figured it out :confused: If so, im sure your at 450+ FSB now right :p
 
Yeah! I'm at 3280mhz now. I don't remember changing that setting on my P4 (maybe it wasn't needed). Oh well, I'll just mark it up to another OC learning experience.

Thanks everyone for the input.

Just as a precaution I installed the floppy drive and I'm running memtest on the ram.
The first piece ran 2 passes fine and the second piece is almost thru it's first pass.

Now if I can figure out why XP is bogging down.
If I go to the menus and select a group that has sub items (like the gigabyte menu), it shows a blank menu outline and then the items fill in about 5 seconds later.

With the new video card I expected graphic displays to speed up. I always run with classic mode and all the eye candy options turned off.

I'm running a new WD 80gb sata II HDD. Could it be something with the drive or controller?

I've done lots of XP installs and have never seen this poor performance before.
 
If you have a sound blaster card (XF-i, audigy2, etc..) Go to RUN, and type "msconfig" go to startup tab, and see if you have a file call "DLLML" if so, that might be your slowdown, uncheck the box, and reboot. This worked for me, as I had the EXACT same issue as you.
 
After testing each piece of ram, XP is running fine. It's something I should have checked first, but maybe I didn't have one of the ram modules fully seated?
Anyway, its time to start stress testing. I started windows at 3319 but I suspect it won't be stable without further tweaking.

I am very happy with the big typhoon cooler. It's almost silent and it seems to be keeping the temp at a reasonable level. It also fits much better then the Ninja Plus I sent back.

It's fins are up higher, so there is no problem clearing the mobo components. Since it's fan blow down, It also provides a slight airflow to the northbridge.
 
Great ! Don't forget to put a small fan on top the Northbridge HS.
What is your current voltage now for MCH FSB and CPU ?
 
whiskey29 said:
Great ! Don't forget to put a small fan on top the Northbridge HS.
What is your current voltage now for MCH FSB and CPU ?

The cpu voltage is at 1.31 (default), MCH and FSB are both +.1
A question about core temp. I'm running the Orthos beta and Super Pi. I'm at 3319 Mhz

PC Health in the gigabyte EasyTune app, shows 52C, which I'm thrilled with.
The Core Temp app says each core is at 60C (which I'm not happy with).

Which of these should I believe? Is there something else I should use to check the temp?
 
I downloaded the Intel Thermal Analysis Tool (TAT)

At idle (@3239 my temps are:
Everest - 51C
Core Temp - 51C
TAT - 51C
Gigabyte - 40C

In this case I assume majority wins. Although I would like to believe the gigabyte temp, I have to assume the temp is nearer to 50C then 40C.

So now the question is, how high can I go? I thought that 60C was the limit, but I am seeing screenshots in the Conroe database thread with temps of 65C!
If I run Orthos - my temp goes up to 65C in three out of 4 indicators. I have no baseline reference here. Is 65C okay for a multi hour stress test?
 
Core temp reads the actual CORE temp :p , The gigabyte's easy tune software reads diode temp (I belive) that is why the temps are different. Core temp is what a majority of us use now, so I would go with that. BTW, awesome OC with minimal voltage, I am so jealous.....
 
i turned off virtualization and set ram multi to 2 and i hit 429(3.0ghz) on F3. i dont know if that helps, im just really proud!!!!! its prime time!
 
newls1 said:
Core temp reads the actual CORE temp :p , The gigabyte's easy tune software reads diode temp (I belive) that is why the temps are different. Core temp is what a majority of us use now, so I would go with that. BTW, awesome OC with minimal voltage, I am so jealous.....

I think your correct about easy tune using the diode temp. I remember reading that in another thread.
I'm going to try lapping my heatsink to see if I can drop my idle temp. Right now at 3279 its running 54C, which is higher than I would like. After 2.5 hours of Orthos the temp held at 63C.
 
GrumpBob said:
I think your correct about easy tune using the diode temp. I remember reading that in another thread.
I'm going to try lapping my heatsink to see if I can drop my idle temp. Right now at 3279 its running 54C, which is higher than I would like. After 2.5 hours of Orthos the temp held at 63C.
I lapped my E6300 and my scythe infinity last week, and it made a 3-4c drop. I think that is wonderful considering this mod only cost me about 10 dollars. (actually $10 is alot since im currently un-emplyeed :( ) Anyone what to hire me :confused:
 
Moddest Mouse said:
i turned off virtualization and set ram multi to 2 and i hit 429(3.0ghz) on F3. i dont know if that helps, im just really proud!!!!! its prime time!

Do as this post said. set ram multi to 2 and you can go over 400 easily. I forgot to set and was not able to go over 400 until I did.
 
There is some great information in this thread, especially for DS3 owners. I'm waiting for my RAM to arrive (hopefully Wednesday) to complete my build.

Are there any stickies that compile all this information anywhere? (Bios settings, memory dividers, fans on the northbridge heatsink, ect...

Also, in regards to the northbridge, Whisky29, were you suggesting a Northbridge cooler or just a plain old 40mm fan screwed into the heatsink?

Finally, if I do grab a small fan for that, where do I plug it in? I see 2 fan headers on my DS3...one says SYS_FAN and the other CPU_FAN. Do I need to buy a fan controller, especially if I add a front mounted 120mm to my case?

Sorry, I'm sorta new at this stuff.

Rich
 
Cintirich said:
There is some great information in this thread, especially for DS3 owners. I'm waiting for my RAM to arrive (hopefully Wednesday) to complete my build.

Are there any stickies that compile all this information anywhere? (Bios settings, memory dividers, fans on the northbridge heatsink, ect...

Also, in regards to the northbridge, Whisky29, were you suggesting a Northbridge cooler or just a plain old 40mm fan screwed into the heatsink?

Finally, if I do grab a small fan for that, where do I plug it in? I see 2 fan headers on my DS3...one says SYS_FAN and the other CPU_FAN. Do I need to buy a fan controller, especially if I add a front mounted 120mm to my case?

Sorry, I'm sorta new at this stuff.

Rich

1- set host clock control to enable
2- set host frequency (FSB) to 333 to start (then increase more to a desire speed)
3- Set RAM multi to 2
4- set your RAM timing to the spec or higher if u want to overlock more (ex: 5-5-5-15)
Don't forget to hit CONTROL+F1 to open the RAM timing setting.
5- set system volt to manual (to keep the bios from auto set it high)
6- increase your ram volt and/or cpu volt as needed.

Both NB and SB will be very hot to touch. for a cheap and effective solution, put a 40mm fan on the top of the NB and tie it up with a small electrical copper wire. you can plug this fan into the Sys fan or use the regular 4-bin PS plug.

when you use core temp or Easytune, the system temp reading is actually from the SB temp, not NB. I used a slot attached fan to blow air over the SB.

if noice is your concern, definitely get the fan controller. I did not realize this until much later on when I got 7 fans running. cheap and good controller is the Sunbeam. I got bad experience with unreliable Vantec controller.
 
Cintirich said:
There is some great information in this thread, especially for DS3 owners. I'm waiting for my RAM to arrive (hopefully Wednesday) to complete my build.

Are there any stickies that compile all this information anywhere? (Bios settings, memory dividers, fans on the northbridge heatsink, ect...

Also, in regards to the northbridge, Whisky29, were you suggesting a Northbridge cooler or just a plain old 40mm fan screwed into the heatsink?

Finally, if I do grab a small fan for that, where do I plug it in? I see 2 fan headers on my DS3...one says SYS_FAN and the other CPU_FAN. Do I need to buy a fan controller, especially if I add a front mounted 120mm to my case?

Sorry, I'm sorta new at this stuff.

Rich
Rich, here are my DS3 BIOS settings:

In the advanced Bios tab
CPU EIST - disabled
Virtualization technology - disabled

Under Mb Intelligent Tweaker
CPU Host Clock Multiplier - 2
CPU Host Clock Control - Enable
CPU Host frequency - start at 333 and work your way up
PCI Express frequency - 100
CIA2 - disabled

Dram timing selectable - manual
NOTE: These settings are RAM specific. These are for ram rated at 5-5-5-12
I only adjusted because my ram was reporting 5-5-5-18 instead of 5-5-5-12

CAS latency time - 5
Dram RAS# to Cas delay - 5
Dram RAS# Precharge - 5
Precharge delay - 12
Memory performance enhance - normal

Voltages
MCH +.1
FSB +.1
vCore - default (move up from the default in small increments if needed. I've read that you
shouldn't go above 1.4?)

I'm currently running an E6400 at 3279Mhz @50C with these settings.

Don't believe the Gigabyte easy tune temp reading.

Download the Intel Thermal Analysis tool (TAT) or Core Temp. Both are more accurate for an overclockers needs. TAT is hard to find.
I got it from here http://shintai.ambition.cz/files/tat.exe

Good luck
 
GrumpBob said:
The cpu voltage is at 1.31 (default), MCH and FSB are both +.1
A question about core temp. I'm running the Orthos beta and Super Pi. I'm at 3319 Mhz

PC Health in the gigabyte EasyTune app, shows 52C, which I'm thrilled with.
The Core Temp app says each core is at 60C (which I'm not happy with).

Which of these should I believe? Is there something else I should use to check the temp?

Easy Tune and core temp are measuring different things. I would go with core temp...it's measuring the actual temp from the processor itself.
 
Temp update
I was really unhappy with my temps, so I removed my HS for lapping. I saw that I had put on too much AS5. I lapped the HS and applied the correct "1/2 rice grain" drop of AS5.

I ran Orthos for 2hrs at 3297mhz. Max temp from TAT was 53C. Thats a 12C drop!
I upped my speed to 3308 and ran Orthos for 4hrs.The max temp was 55C.This is still at default vcore.

I'm satisfied. My goal when overclocking has always been to go past the top end cpu in the same lineup. Getting to 3.3Ghz more than meets that goal. I figure I paid $250 for a cpu that is running at $1000 speeds.
 
The DS3 is 1 hell of a motherboard isn't it :) Cool, glad you met your goal. Now make a sig up so we can all see it :p
 
GrumpBob said:
Temp update
I was really unhappy with my temps, so I removed my HS for lapping. I saw that I had put on too much AS5. I lapped the HS and applied the correct "1/2 rice grain" drop of AS5.
I was wondering about that. A lot of guides I saw said to put a small "pea sized" dollop of AS5 on the proc and spread it around.

On Artic Silver's website, they said to put it in a line down the center of the proc, install the HSF, and rotate the the HSF a couple degrees to the right and left before locking it in.

That's the method I used and I'm just wondering if anyone else does that? My RAM won't be here 'til Thursday so I'm thinking of taking off the HSF and reapplying the AS5.
 
Ordered my DS3 last night. I'll be piecing my rig together this weekend...

e6600 ($285)
2gb corsair XMS2-5400 675mhz ram ($160 AR)
DS3 board ($145)
Raptor 150gb ($195 AR)
PNY 7900GTX OC edition ( $300)
500w Ultra V-Series PSU ( $0 AR)
Antec P180 ($110)

Im just looking for a modest OC of 9 * 333 to get 3ghz then not have to open my case again until it's time to dust it out. Sounds like it should be an easy OC. :cool:
 
MoggSquad said:
Ordered my DS3 last night. I'll be piecing my rig together this weekend...

e6600 ($285)
2gb corsair XMS2-5400 675mhz ram ($160 AR)
DS3 board ($145)
Raptor 150gb ($195 AR)
PNY 7900GTX OC edition ( $300)
500w Ultra V-Series PSU ( $0 AR)
Antec P180 ($110)

Im just looking for a modest OC of 9 * 333 to get 3ghz then not have to open my case again until it's time to dust it out. Sounds like it should be an easy OC. :cool:
Dont take this the wrong way, but your PSU is terrible, this might be why it is free after rebate ;) . and PNY tends to use the lowest "BINNED" chips for there cards, so dont have your heart set on a good OC..... Im not an ass, but just giving you a heads up :cool:
 
newls1 said:
Dont take this the wrong way, but your PSU is terrible, this might be why it is free after rebate ;) . and PNY tends to use the lowest "BINNED" chips for there cards, so dont have your heart set on a good OC..... Im not an ass, but just giving you a heads up :cool:

I wont be OCing the card, it's factory OC'd. http://www2.pny.com/7900-GTX-512MB-PCIe-P1729C14.aspx

I'm aware the PSU isn't the best. I read a review about the PSU. They didnt have anything bad to say, but as the same time they didnt say anything that makes it shine. I'll give it a try and see how it does. If it's that flaky I'll replace it.
 
Back
Top