Help! Continuous failure of Prime95!

M00saysthebone2

Limp Gawd
Joined
Sep 10, 2004
Messages
348
Well, I ran into some problems with BSOD randomly after about 3 nights of idle (I use my 2nd computer a lot and the other one just idles). So I decided to run Prime95. Here are the specs
Athlon 64 (Socket 939) 3500+
MSI Neo2 Platinum
Corsair XMS PC3500 2x512 (BH5)
WD 36GB Raptor
Fortron 530W PSU
Radeon 9800XT
With this, it failed at about 2 hours. So i swap out the power supply with a 420 Thermaltake. It then failed at TWO MINUTES! What do you guys reccomend I do?
 
prime usually fails under 2 things, bad memory, or overclocking, if you're overclocking, stop. Otherwise grab memtest and test the hell out of your memory.
 
Got to agree with defakto here - get Memtest86+ up and running. Enable all tests, let it go all night. I'll be the answer will be obvious in the AM.

FWIW - every new build I do starts with Memtest86+ and the drive mfgr's diagnostics before I install the OS, and Prime95 / 3DMark loops after. They don't leave the bench until all those tests pass cleanly, with no errors. At a minimum, I like to see Prime run at least an hour or two and 3DMark for at least four hours without errors.

Good Luck - B.B.S.
 
I hear a lot of memory doesnt go well with Socket 939 so far. Do you think mabie its the motherboard is incompatable with my memory? Im not quite sure what to think, but i just started running memtest86+ with "all tests" selected. If I should do anything else or more, please tell me. Thanks for the help [H]!
 
Oh, forgot to ask. Assuming this does find an error or 2, does it simply prove the memory is bad? Like i said though, if this finds nothing (which I think its not going to find anything because I used this in a previous system w/ no problems).`
 
i means the memory is bad, just not that bad...

if you switched PSUs and got it faster, try getting a power conditioner... (battery backup or similer)
 
well with the fortron 530, it went 2 hours, with the thermaltake the first time it went 5 min, the 2nd time with thermaltake it went 2 hours. So i dont think its the PSU, especially because I only have 1xHD, 1xDVDBurner, Vid card, sound card, and mobo/cpu.
 
hmm, possibly motherboard issue then? maybe a bad voltage regulator somewhere?
 
My BH5 3500 memory likes 2-3-10-2-1T timings, 2-2-2 would cause failures in memtest. I would try that if you havent already and see if the problem goes away.
 
Well, heres another background story
I tried the abit ver of the Socket 939, and it didnt work, I got BSOD after BSOD...constantly...over and over...so I bought the new MSI Neo 2 Platinum...I get BSOD still, but not as often as before.

Now as for the memory, it is BH5 Corsair PC3500 like I said, but I leave my BIOS at defaults. (namely because i dont know how to properly oc memory). I look in the memory section of my bios, and I expect to see 4 timings, but i dont understand everything. If Fail safe settings are supposed to work too, then I guess thats fine, but if it works with 2-3-10-2-1T settings, please let me know what i need to change exactly
Memtest86+ has been running now for 25 min. With 0 errors.
 
alright guys. Left it on overnight, 0 errors, its at test 11, and it got through "one pass" with 0 errors. I knew this would happen :(. Ive used the memory before and I didnt think there was anything wrong with it. Anymore ideas? Im still leaving it on during classes, if I still dont get any errors ill pop some OCZ PC3200 twin pack in and run prime 95, if thats not it, it must be something else. What are the other possibilities for prime 95 failure?
 
alright, my memory has been running for 24 hours exactly. Does anymore have anymore tips before I try switching out the RAM? What should I test and how ? :(
 
Back
Top