Gosh Darned Intel Board

Dan_D

Cat Can't Scratch It
Joined
Feb 9, 2002
Messages
66,323
Ok. I am about ready to throw this fucking intel D865PERL board in the fucking trash. It's not even my board. It belongs to a friend of mine.

I have tried everything I can think of to make this son of a bitch work right. The system runs dog ass slow. It is also unstable. I never get a temperature over 113F. I am not sure what that is in C. But needless to say it's not overly hot.

I can't get the system to behave well enough to do a whole hell of a lot with it. It locks up and crashes all the damn time. It's amazing I even got Windows XP to install. I have the service packs and critical updates installed. I also have the latest Intel chipset drivers loaded.

I found out on the intel site that if you are going to run an 800MHz FSB chip on this thing that you have to do a BIOS update. GREAT. So thats yet another thing I have had to do. Still no dice. It acts the same way. Volt meter confirms that power output is normal.

I switched processors out with a 2.0GHz 400MHz FSB Pentium 4 Northwood. Again it acts the same way. I have tried 3 different sticks of PC2100 ram in the fucking thing. Still acts the same.

I am really starting to get pissed off. So much so that I can't think straight.

I normally stick with Asus boards and have never had issues like this. However my buddy didn't want to spend the money on the i875P board that I've got. Not that I blame him.

The machine configuration is as fallows.

Antec case and power supply 300Watt
Intel D865 PERL motherboard
Maxtor 40GB HD 7200RPM single drive. No RAID configuration or anything.

One SB Live add in card.

Video PNY Geforce 4 Ti 4200 64MB card.
And the memory is a stick of 512MB Mushkin PC2100 ram.

I know not the greatest specs but like I said this thing doesnt belong to me. Any thoughts guys? Thanks.

**EDIT**
From the Rules: "No CUSSING in the subject lines, this is grounds for immediate removal of your posting privileges." MD
 
I checked one other thing just a second ago. For some very odd reason with either processor I have installed, the CPU usage on startup even in safe mode is 100%.

WTF???
 
have you checked Task Manager to see what process was using 100%?

have you checked the board to see what kind of voltages the cpu is getting? (this you can measure on the mosfet legs near the cpu socket).

also, have you checked the board over real good for any mis-colored parts or caps with domed tops on them (which means they're either already blown or damned close to it). Blown caps would cause instability, and are one of the easier things to fix. just pick up some that match the original, de-solder and remove the original, then put the new one in and solder.

I had stability issues on an Abit VP6 a couple years ago. had about 6 caps that were blown. replaced all six in about an hour (may have taken less time if I wasn't watching tv at the same time)
 
Originally posted by nst6563
have you checked Task Manager to see what process was using 100%?

have you checked the board to see what kind of voltages the cpu is getting? (this you can measure on the mosfet legs near the cpu socket).

also, have you checked the board over real good for any mis-colored parts or caps with domed tops on them (which means they're either already blown or damned close to it). Blown caps would cause instability, and are one of the easier things to fix. just pick up some that match the original, de-solder and remove the original, then put the new one in and solder.

I had stability issues on an Abit VP6 a couple years ago. had about 6 caps that were blown. replaced all six in about an hour (may have taken less time if I wasn't watching tv at the same time)

Task manager is a good start.

Did you try fail Safe BIOS settings? Remove components or disable them in the BIOS until you're running just the video card and PS2 ports, plus whatever else you actually need to get it running.

You now have a good idea how frusterated I was with my Tyan Tiger 100 the other night. I finally found out that my issue was something really stupid... I was overclocking the poor thing a little too much. That caused some issues with my RAM, and thus, instability.
 
If it's a 100% pure Intel board, I really doubt he's got any options on there to oc anything with. Intel makes their boards for stability over performance....kind of like most OEM's.
 
Originally posted by nst6563
have you checked Task Manager to see what process was using 100%?

have you checked the board to see what kind of voltages the cpu is getting? (this you can measure on the mosfet legs near the cpu socket).

also, have you checked the board over real good for any mis-colored parts or caps with domed tops on them (which means they're either already blown or damned close to it). Blown caps would cause instability, and are one of the easier things to fix. just pick up some that match the original, de-solder and remove the original, then put the new one in and solder.

I had stability issues on an Abit VP6 a couple years ago. had about 6 caps that were blown. replaced all six in about an hour (may have taken less time if I wasn't watching tv at the same time)

Well I have checked for damaged or blown components. I do not have a voltmeter. I was not able to see any process that was taking that much CPU usage.

According to the BIOS the CPU voltages are right on. I suppose I should have mentioned all of that. I was so pissed off last night I couldn't think straight.
 
Originally posted by nst6563
If it's a 100% pure Intel board, I really doubt he's got any options on there to oc anything with. Intel makes their boards for stability over performance....kind of like most OEM's.

Yeah the only thing you can mess with is memory timings. You really can't OC with this board to easily. And I am not even going to attempt to since its not my machine.

Thats also part of the reason I recommended the board to him. I've used intel boards before and have had great luck with them.

I've also checked and changed BIOS settings removed uneeded devices and still no go. I haven't even been able to load the video card drivers yet. That's how bad the slowness is.
 
Would you be able to sneak in another board into that computer and see how the rest of the system behaves with another motherboard running it?
 
Well I replaced the board with another identical board. Stability seemed to be fine. But now I am getting IO errors and file copying errors anytime I do almost anything.

So at this point I am thinking the drives hosed. I have tried replacing cables and changing BIOS settings. But the system does act better with the new board then it did with the old one.

So I'll slap a new HD in it tommarow and see what I get.
 
Maybe it's a bad board, or some other component is flaky? We've built 6 machines in the last three months with that board and never had any issues with it.
 
Well I have tried two different processors. 5 different sticks of ram. Including Corsair and Samsung DDR400 low latency modules.

I have tried two Maxtor Hard drives. One 40GB drive and one 100GB drive. I have also tried two different video cards.

I have tried several different drive cables and swapped channels around. What's interesting is that this second board behaves nicer than the last one did.

I am at least getting the same results in my failed attempts to load an OS now.

I get file copy errors fairly often. And when it gets to the part where it wants to detect devices it locks up. Goes no further. It just sits there for about an hour if I let it.

I am trying a Western Digital drive now. Both Maxtors I tried were from the same series of drives. Not to mention they are both fairly old.

I also have another identical 40GB Maxtor that is the same as the original drive in the machine. So I still have a couple options. Just not many. I am about to tell him to take it back and spring for an Asus instead. Boards that I have had tremendous luck with in the past.
 
Ok the piece of shit just blew up in the same fucking spots as the Maxtors did. So with the Western Digital it makes no difference.

I fucking hate this board. BIOS updates, processors different ram chips, none of this shit makes any difference. The fucker acts the same way every fucking time.

I have built several systems with intel boards. I have several friends that are running intel boards in their systems without a single problem. But I have had TWO of these fucking things now. I don't see how I could be having a compatibilty problem with another component seeing as how I have changed everything now and one point or ANOTHER. FUCK!!!!!!!!!!!!

Next is the power supply. Since I don't have a damn volt meter. However I don't relish the idea of ripping mine out of my machine just to test this pile of crap.

I am really pissed off now.
 
are you running the board outside of the case? if not, you may want to give that a try. could be something shorting out that's not serious enough to make the board shut itself down.

I'd try the powersupply though...
 
Well I've got Windows Installed now. All it took was the removal of the Geforce 4 Ti 4200. I dropped in an Geforce 2 MX 440 instead for test purposes.

The problems have been reduced alot. However I still get IO problems. Such as the system telling me that half the downloads or executables I try and unpack are corrupted. It does it for almost anything. Off of CD's the web any place. The system will often just reboot for no apparent reason when I am working with it also. Not to often. Usually only when I try to install something.

My temperatures are good too. Nothing over 109F. Not awesome by any standards but for a mini-tower case and stock cooling its not bad at all.

I am so sick of this board. All the components work just fine anywhere else. As far as the PSU goes I really would rather not check that if I could avoid it. I do not want to take it out of my other machine. That's way to much trouble for a system that isn't even mine.

Not to mention I have all my wires in my case neat and zip tied. And I am out of zip ties.

I've got all the latest drivers for everything. Windows XP has all the current service packs and patches.

And other than the PSU I have replaced EVERYTHING. So before I go screwing with the PSU does anyone have any other suggestions?

I'm tempted to tell him to go out and by a Asus P4C800-E since I can't find P4P800's locally in my area.
 
ive had 5 friends go crazy over this problem, and myself included. take out the sb live. thats what it was for all of us, random reboots, corrupted files, errors up the ass. i went thru every system in my house in two months, thinking id lost them all but it was the freaking sb live i kept putting in. creative doesent get another cent from me.

edit...

i know you say all the components work fine everywhere else, but that happened to me also, my p4 rig was toast with the sblive in it, but my p3 rig was fine for a couple weeks, weirdness, but thats the way it is.
 
Well I pulled the SB Live! out and it still screws up. :)

Guess my problem is different. Well tommarow we are going to take the power supply and case back and change over to an Asus P4C800-E instead.

Rather than screw with testing between the two remaining components I am just going to do it that way. And I will probably talk him into using the onboard audio as it isn't bad at all. The SB cards drivers suck ass.

Creative and there stupid patches and ghey driver downloads. Its such a pain in the ass to just get Creative Drivers that don't depend on pre-installed drivers off of the CD's they came with.
 
Also look into the p4s800d-e deluxe... excelent performer and dirt cheap. Unless you have your heart set on Intel based.
 
I cant stand non-intel chipset boards. They tend to give me problems. I've had horrible luck with them. I would consider VIA based if need be. I would however NEVER use SIS or anything else.

Personal experiences with non-Intel chipsets has not been good. But I did solve my problem. It turned out that it wasnt the PSU. So it was the board AGAIN. I don't know what in the system was causing the problems or if it was two bad boards in a row. Which I would find difficult to except considering the quality of Intel boards in general.

I switched to a P4C800 Deluxe and haven't had a single problem since. I just got done with the system a little while ago.

Thanks for the help and suggestions though. I just had horrid luck with that brand of board this time around.
 
Back
Top