good way to put a rad?

Nek

Weaksauce
Joined
Oct 24, 2004
Messages
70
I don't know if this is possible or not, I try not to drill any holes in the case, simply because I don't have the tools :(
I don't even know if the screws are strong enough to hold the rad and the fans



untitled8vm.png


Any other suggestions?
 
I think it would be better to have all your fans going in the same direction away from the case. I have used similar mounting techniques and it works just fine. Just be careful when putting the holes all the way through your radiator. BTW, what specific radiator are you planning on doing this with?
 
You will want to have some fans that can push a lot of air to utilize the full capacity of that radiator. Also the factory holes on that radiator can be easily hand tapped with a 6-32 thread. You can then get some 6-32 threaded rod at the hardware store and use that to mount your radiator. :)
 
You don't have to do push/pull you know. :-P It's not that much better (I think I read 20% real cooling increase/50% more air moved) and it's double the dBA. Plus it will be lighter.

Then you will be able to stick the rad right up against the case and it will have a center of gravity much closer to the case. I wouldn't worry about it in that position.
 
Russ said:
You don't have to do push/pull you know. :-P It's not that much better (I think I read 20% real cooling increase/50% more air moved) and it's double the dBA. Plus it will be lighter.

Then you will be able to stick the rad right up against the case and it will have a center of gravity much closer to the case. I wouldn't worry about it in that position.

I don't think the rad fits up against the back the the case...

it's a Lian-Li PC-7AW
 
I like the basic idea, leave the fan direction to you, it can be changed/played with easy enough and that will be some fun too. :D


Here are some suggestions for you to chew on.

You are hanging a fair amount of weight, dont forget it will have water in it, and most common screws you find in hardware stores are not made of the best steel, actually they are fairly soft crap metal. I am worried about sag and also stiffening up the whole assembly.

use stainless steel threaded rods instead of the long screws (SS long screws would be ok too) if you can find them with the proper thread size.

where you have the two nuts you could replace it with a spacer (hollow tube that the threaded rod goes thru, cut to the length you need. This would also help to make the assembly stiffer and stronger, eliminate the need to individually tighten a bunch of nuts. If you use the treaded rod a nice wing nut or big thumb screw on the end thats on the outside of the case would finish it off and allow easy quick disassembly for cleaning etc. Toss a split lockwasher in there somewhere too.

another set of screws or rods with spacers on the bottom mounting holes of the bottom fan going out to the back and thru the case to the outside would also give you a lot more mechanical integrity. You would have to drill small holes in the case. Perhaps there is some stuff there you need to clear and cant put them there Even another set on the uppper mounting holes of the bottom fan would help.

find something you can chop up to make rubber blocks to stuff inbetween the rad shroud and the fins if it would be possible for the screw/rod to be threaded in so far it could hit the fins. This may not be needed, I dont have one of those rads.

The "speciality" hardware drawers are your friend :p


edit: oops just saw the bit about no tools to drill holes, bah, someone you know can lend you a drill with a 3/8 bit for a hour,
 
Russ said:
You don't have to do push/pull you know. :-P It's not that much better (I think I read 20% real cooling increase/50% more air moved) and it's double the dBA. Plus it will be lighter.


Just some info.

2 fans running at 35.5db do not add up to be 71db. The increase of 2 35.5db fans would only be maybe 5db. There was a thread about this a couple months back.
 
well twice the noise or so. decibel increase exponentially in noise. I'm not saying that's right. I kinda just put in the dBA thing because I didn't want to go google it and spend a lot of time looking it up. I just know that it's gonna be noisier.
 
Yeah, when I get that rad, I will see if the mounting holes go through the whole thing or not

if it does, then I can maybe find 4 really long screws to go through the whole thing, fans and all

and how soft are Lian Li cases? all I got that I think are useful is a hammer and some nails.. maybe I can like puncture a couple of more holes for the bottom fans
 
Nek said:
and how soft are Lian Li cases? all I got that I think are useful is a hammer and some nails.. maybe I can like puncture a couple of more holes for the bottom fans

I would definitely not do that as you will probably only end up with a big dent in the bottom of your case. That floor is about 2mm thick :eek:
 
Nek said:
and how soft are Lian Li cases? all I got that I think are useful is a hammer and some nails.. maybe I can like puncture a couple of more holes for the bottom fans

NO. Don't do that. That case has done nothing to you.
 
well I found some kind of drill, but it has like a screw driver head on it, and I don't think I have a drill bit... it's spinning kinda slow and I can't seem find the rechargeable battery charger :(
 
dremels aren't that expensive are they? You could probably get one off of ebay for like 40$ shipped. I say save the money and mod your case the right way. Dont be going around messing up your nice Lian-Li all willy nilly!
 
Back
Top