Gigabyte P35-DQ6 forgetting settings problem(Permanent solution?)

sram

[H]ard|Gawd
2FA
Joined
Jul 30, 2007
Messages
1,854
Hi all. I'm sure some of you encountered this problem with gigabytes mobos when you save your overclock for example and come at a later time to see it back to default settings. Has a permanent solution been found to this problem? I have the latest BIOS of course but that does nothing to remedy the problem.

When I first noticed the problem in my mobo, I had to remove the cmos battery for some time before the mobo can get into normal operation. Now, it just goes back to default and I had to go BIOS setup and load my saved profile. But still, that is annoying as hell.

It is not worth it to change the mobo at this time of course. What do you think I should do? Any comments? Suggestions?

Thanks.
 
The battery is probably dying / on it's way out. P35 boards are quite old now (going on 5 years). Replacing the CMOS battery may fix your problem (it's also pretty cheap).
 
The battery is probably dying / on it's way out. P35 boards are quite old now (going on 5 years). Replacing the CMOS battery may fix your problem (it's also pretty cheap).

Highly unlikely. This has been the case since the very beginning.
 
I had a Gigabyte P35 mobo too and it did the same from day one. The behavior (OC settings not sticking) was called by some the Gigabyte "stupid mode", usually there is a setting that triggers the mobo's boot failure guard mechanism and you have to load the previously saved OC profile (not a biggie). Sometimes disabling the Legacy USB storage detect function in the bios or a clrmos helped, but I suspect, some voltage or the memory multiplier isn't applied correctly at the boot sequence... don't know. :(

P.S.: it wouldn't help any BIOS update, trust me.
 
sram, maybe you have over "over-clock" your system.
As Seb1 mentioned Gigabyte has this "Stupid mode for protection against system over voltage", it will auto set the bios into default value.
If you just set little over clocking will the system also back to default value.
As you may know, over clocking success depend on many factors such as CPU, CPU fan cooler, memory, power supply, bios setting and others....
 
sram, maybe you have over "over-clock" your system.
As Seb1 mentioned Gigabyte has this "Stupid mode for protection against system over voltage", it will auto set the bios into default value.
If you just set little over clocking will the system also back to default value.
As you may know, over clocking success depend on many factors such as CPU, CPU fan cooler, memory, power supply, bios setting and others....

No No, don't think that's the reason. It is just the stupid BIOS. I'm at 3.5 GHz and my temps are really low. And it can stay at 3.5 GHz for a month for example. It just does it from time to time. If it is overclocking, it will insist in going back to default every time, however, that is not the case. It will sometime go back after one week, maybe after one month, maybe longer.....

Thanks.
 
Hi all. I'm sure some of you encountered this problem with gigabytes mobos when you save your overclock for example and come at a later time to see it back to default settings. Has a permanent solution been found to this problem? I have the latest BIOS of course but that does nothing to remedy the problem.

When I first noticed the problem in my mobo, I had to remove the cmos battery for some time before the mobo can get into normal operation. Now, it just goes back to default and I had to go BIOS setup and load my saved profile. But still, that is annoying as hell.

It is not worth it to change the mobo at this time of course. What do you think I should do? Any comments? Suggestions?

Thanks.

You can never permanently fix this, and the problem happened on all C2D capable chip set (P965/P35/P45.) I went through a couple of boards and one of my friends still has one that just drops his settings every couple of months. For a while on this forum and other anytime someone made a post like "My settings are not working" and "BIOS keeps going back to defaults" you could be almost certain it was someone with a Gigabyte Intel board. Anyway after fighting with it for months, I was more satisfied than ever when I finally got a board from a different manufacturer.

Also the problem isn't over volt or overclock protection because when those trigger, the BIOS tells you. Also after that happens, changing the BIOS settings still works. When the stupid mode kicks in, you need to pull the battery or flip the CMOS reset jump while the system is unplugged for about 15 minutes to fix it.

I contacted Gigabyte a few times and when I would get a response in English, they still had no idea what I was talking about.
 
Back
Top