Gigabyte DS3... No Video

lightsourcex

Weaksauce
Joined
Jun 8, 2006
Messages
97
Ok, well I was up and with running this memory: http://www.newegg.com/Product/Product.asp?Item=N82E16820231084

Everything was fine, I installed GRAW and played for about 15-20 minutes.

Everything was going great until I ran Super Pi, I got a NOT EXACT ROUND error, and my pc restarted, but the monitor went off. And now I can't get video signal.

This is what I've tried (Clearing CMOS each time):

Switching Memory (Stick 1, Slot 1 & 3 // Stick 2, Slot 1 & 3)
Disconnecting All Drives & Only leaving MEM, CPU, & GPU.
Using PCI Video Card
Booting W/O any ram (fast beeping)
And now, I'm just leaving the system off w/ the power cord disconnected and CMOS battery out for a few hours.

Any idea's or Suggestions?

System Specs:

INTEL C2D E6300 (Allendale) @ 1.83GHz w/ XP-120 | GIGABYTE DS3 | G.SKILL 2x1GB DDR2 800 (2GBNR) | eVGA GeForce 6800GT @ 400/1100 w/ Zalman VF-900 | OCZ PowerStream 520W | Thermalright XP-120 @ 96CFM | Lian Li PC-7B | Seagate 320GB (PWT)
 
category_five said:
are your fans spinning

Yes they are.

demografik said:
Do you get any beeps? Were you monitoring temps?

Beeps, yes, actually I only got one beep when my system DID work, but afterwards I got nothing. Except for when I took all the memory out. Which was fast beeping but that's obvious.

--

I didn't get enough responses or help, so I'll RMA the mobo & ram today.
 
No beeps generally means motherboard or processor. Don't mess with the ram, 90/10 it's the processor.
 
demografik said:
No beeps generally means motherboard or processor. Don't mess with the ram, 90/10 it's the processor.

How could it be the processor?

Take this into account... My ram runs at 1.9 voltage, but I had it set to 1.8, I run a cpu/memory intensive program, and I get a NOT EXACT ROUND error, which (from ddr1 days) meant that memory wasn't high enough in voltage, on top of that, the processor was nowhere near to overheating seeing as the max load temp I got on my XP-120 w 40% fan power was 35C.

jimmyz said:
if you don't know what is wrong don,t rma anything. you need to find your problem first or you will be in the same boat when you get your other mobo.

I understand this, but it seems as if everything is pointing to my MOBO / MEM.

The reason I say that is when I overclocked on my DDR1 system, when my voltage was too low on my memory I would always get NOT EXACT ROUND errors, nothing pointed to CPU because it never seemed to have a problem.


I would like to find out what the EXACT problem is as you say, but there's no help that I'm getting that can help me test that. I've tried just about everything and I still am not getting any good results, so I figure that if I replace the two most suspicious parts, that I'll get the best results.

People've told me to test the DDR2 on someone elses mobo, but no one I know has a mobo supporting DDR2. I have a friend with an LGA775 motherboard but its an olderchipset (865 I believe) and that can't run Allendale/Conroe.

So, I'm basicaly S.O.L... If the motherboard & ram comes back and dosen't work, then I'll take into consideration that its the CPU. Otherwise, I'm guessing CPU/MOBO.

Can't be the videocard either because both my PCI & PCI Express video cards don't work in the crashed system but the PCI works in my agp system (current).
 
That error could be RAM or CPU, superPI doesn't specify. If the problem was your RAM, you would be getting RAM ERROR beep codes at post. Otherwise, it's definitely either the motherboard or processor. The fast beeping when you took the ram out indicates that the motherboard was able to realize there was no ram in, meaning it's less likely to have a problem, therefore pointing more towards the processor.
 
demografik said:
That error could be RAM or CPU, superPI doesn't specify. If the problem was your RAM, you would be getting RAM ERROR beep codes at post. Otherwise, it's definitely either the motherboard or processor. The fast beeping when you took the ram out indicates that the motherboard was able to realize there was no ram in, meaning it's less likely to have a problem, therefore pointing more towards the processor.

Yea. I ultimatley think it's the motherboard and the RAM was just so I wouldn't have to RMA it if it did have a problem.

But we'll see after I get everything back. The package should be back @ newegg tomorrow (today really 12:35AM). 3-5 days for replacement, and 2 days for shipping. I'm suspecting monday to wednesday for return.
 
Well, I got my parts back.

Memory and Motherboard. And I'm currently Up and Running.

As I suspected it was a problem with the memory. I'm currently too cautious/afraid to try Super Pi seeing as to how it was the program that got me messed up in the first place.

So I guess I'll just run all the other tests. I.E. 3DMARK05, AQM3, ETC.

Just not Super Pi until I can be assured that if I do Super Pi it won't do the same thing it did last time.

219025537_dc90dfbc47_o.jpg
 
demografik said:
How are you certain it was ram and not the motherboard?

Oh, I'm not saying it was the memory. I'm saying that the problem had somthing to do WITH the memory, whether it was the memory itself or the voltage not being high enough.

I actually think it was the mobo more than the memory becuase the settings were screwed more than likely.

newstuff3pu3.jpg


I've tested for about 1 hr, but that's it. I was too anxious to get to gaming.

I'm not sure if I'm stable but it sure does seem that way.
 
Back
Top