Gave up on 3.0ghz

acphydro

Limp Gawd
Joined
Jun 9, 2003
Messages
192
Specs in sig.

After trying the past week or so trying to get to the 3.0ghz mark I can't get there stable. Put memory out of the equation and it just wont stay stable at that speed. The more volts I give it the longer it lasts at 3ghz but damn. I'm near 1.5v right now. I don't want to go any higher without some watercooling, and ummm well kinda pointless to buy a watercooling kit and a new case I'd need and other equipment when I could just spend the extra money on a guaranteed faster cpu or etc. This is my first REAL overclock experience. I've mostly only done moderate/minor overclocking. Well here it is passed prime95 dual stable for 28 hours till i killed it at 2.75ghz and memtest passed for 8 hours till i stopped it. Now testing at 2.8ghz.

2.80

2.8.jpg


Also cpu temp is off by around 6C as I tested with a probe as accurate as I could get.
 
What happens if you give it 1.55vcore? According to your temps it looks like it could handle the voltage. Also, does that processor have a 10x multi? If so, I would try that with the increased voltage.


Good Luck!
 
Smoove910 said:
What happens if you give it 1.55vcore? According to your temps it looks like it could handle the voltage. Also, does that processor have a 10x multi? If so, I would try that with the increased voltage.


Good Luck!

Should have mentioned that I did try all the way up to 1.57vcore but I'm not really comfortable going over 1.5 not for heat sakes but for the life of the cpu sakes. I've looked for details on how voltages kill cpus but can't find any concrete information about athlon64 cpus and dying from overvolting. I'd like to have this pc as my main pc for at least the next 2 years probably 3 years though. Happen to know how increased voltages kills these cpus?

Also I didn't try the 10x multi. I'm trying to keep my memory near its spec. I couldn't get my memory running at 275mhz with upto 2.8v, ultra loose timings with 2T settings. That's why I switched down to the 9x multi to get to 2.75ghz with my memclock at 166 to net me ~250mhz. Although at 9/10 with 10x300 gets me ~250mhz also on memory, i took memory out of equation. So I'm rambling a bit here.

What I'd really like to know is what difference does using the 9x or any other value lower as opposed to using the 10x default make?
 
i've been out of the game for a while but isn't 2.8 really good for an x2?

i know many of the single core opties do 3ghz no problem... maybe downgrade to hit 3ghz if you're just facinated with the number.



cheers,

mal
 
This is the highest I got my X2 to, but couldnt get it to stable in Orthos with 3ghz. :confused:

I'm just wondering what normal Idle temps are for X2's? Ive been reading around that people been getting 30-40c Idle. I get around 40c idle, but Im using a Zalman 9500? Shouldnt it be lower? I probably have to much compound on it.:confused:

9h30mstresspv8.jpg
 
I was getting 44c full load under water at 2.6...

So I dont think you're THAT far off.
 
well you cant expect to have the same idle temp when.. your case is cooled differently, and the temperature of your room makes a big difference.

And I wouldn't worry about going to high on voltage on air IF, your temps are hitting high 50's, or you're going over 1.6 on air :)
 
malicious said:
i've been out of the game for a while but isn't 2.8 really good for an x2?

i know many of the single core opties do 3ghz no problem... maybe downgrade to hit 3ghz if you're just facinated with the number.



cheers,

mal

2.8 - 2.9 is normal for x2 3800's, my x2 3800 did 3 Ghz prime stable @ 1.5v
 
dnottis said:
2.8 - 2.9 is normal for x2 3800's, my x2 3800 did 3 Ghz prime stable @ 1.5v


Nahh, 3800's are pretty normal to about 2.6 or 2.7, 2.8ghz and above is VERY rare on average....
 
i'd be pretty happy as is.

although it's good to shoot for a goal, overclocks are still a gift
 
Arghh.. still can't hit 3ghz! I want it bad but just cant stable it enough.
 
I haven't really tried anymore since my last attempt. I couldn't get it stable at anything over 2800 with up to 1.6v. I do realize that overclocks are a gift and I'm very happy at 2.8. I'm running a dual prime blend right now on it at 2.8 so far going strong @ 7hours.

CPU temp reads 40C, PWMIC reads 52C and chipset reads 40C. Which I know to be around 45C, 57C, and 45C respectively. My ambient temp is around 22-27C not exactly sure but its in that range. I don't have any heat going to this room period, if it weren't for multiple electronics in here it would be much colder lol. Sometimes my fingers get really cold but most of the time I'm warm in here. Especially with both pc's going and etc.

I do see that most people don't make it over 2.4-2.6max with these cpus, especially my stepping. But I thought they just didn't tinker enough :p It took some major tinkering to get it stable at 2.60, let alone 2.75. If it passes dual prime, memtest, and a series of 3dmark loops ill be satisfied with 2.8. It's not quite 3.0 but its one hell of an overclock.

I've got my XFX 7900GS @ 620/820 right now and its stable at that speed. So I'm pretty happy with that. Might see about getting another and doing the SLI mod to this board with high hopes of getting another card that will go this high.

Anyhow, does anyone know how the diff multipliers effect things directly? I'm not sure and would just like to learn about it if at all possible. As for now I'll stick with my 2.0@2.8 :D
 
Back
Top