FS: 4x 1GB Crucial Ballistix PC8500 DDR2 1066 5-5-5-15-2T 2.0v

[fubar569]

Fresh back (as in just arrived this afternoon) from Crucial RMA department. all are sealed but ONE stick that i removed to inspect for visuals and will be memtesting this stick later tonight to determine its worthiness.

sticks are as in title...

4x 1GB PC8500 DDR2 1066 5-5-5-15-2T 2.0v w/ LED - NIB fresh from RMA

Looking for 50 plus shipping for all 4 sticks...

heat: fubar569
ebay: lipper540

EDIT: ends in 8FE5 - single sided sticks...awaiting confirmation of my testing but if this is the same 2.2v stuff i sent in the first time i'm gonna rip crucial apart...and i will subsequently lock the thread because the 2.2v spec is what killed the first batch...and i do not want any of you to have the nightmare i went through trying to get them replaced...

EDITEDIT: - memtested a single stick of it at 5-5-5-18-2T (autodetect) at 1066mhz and 2.0v and it passed. i am using it right now. No errors existed through 3.5 passes and it's been in the system for a few hours now and no issues are apparent. I pulled the EPP and the voltage for 1066 is still spec'd at 2.2v but it is running fine at 2.0...I will be emailing crucial about this...

 

[scgt1]

yhpm

 

[PR1M3R]

I have this single sided 1066 2.0v ram fresh from RMA. Same as yours. And it does NOT have the same problems the 2.2v stuff did. Mine also ends in 8FE5.

Does 1150 with 2.12v measured 5-5-515, but I would not recommend overvolting these at all unless you have active cooling.

 

[scgt1]

I have this single sided 1066 2.0v ram fresh from RMA. Same as yours. And it does NOT have the same problems the 2.2v stuff did. Mine also ends in 8FE5.

Does 1150 with 2.12v measured 5-5-515, but I would not recommend overvolting these at all unless you have active cooling.

yhpm and a bump

 

[fubar569]

i just memtested this single stick on auto settings...it detected 5-5-5-18-2T - it passed this at 2.0v at 1066mhz...

i ran CPUZ and the EPP profile still says 2.2v! very odd...i will be emailing crucial about this...

PR1M3R, could you do me a favor and a program that can read the JEDEC/EPP info and read what the voltage is specified to?

 

[fubar569]

BUMP:

I have emailed crucial with regards to my findings...awaiting response...

i can confirm the test stick does 5-5-5-18-2T at 2.0v in my DFI Lanparty DK P35-T2RS motherboard without issue so far...i'd assume the other 3 should do the same...if a prospective buyer would like me to test them in this system i'd be more than happy to...

 

[PR1M3R]

The EPP on mine are 533 @ 5-5-5-15-30 2t @ 2.0v
That is strange that yours have 2.2v in the EPP still.
I use CPU-z

 

[fubar569]

The EPP on mine are 533 @ 5-5-5-15-30 2t @ 2.0v
That is strange that yours have 2.2v in the EPP still.
I use CPU-z

indeed it is! no clue why...but i have emailed crucial yet again to see what they have to say. historically this means about a 7 day wait for a response...

thank you for checking that for me...

oh...and bump