Friend's comp shot?

LPB

n00b
Joined
Jan 13, 2007
Messages
12
I was at a friend's house yesterday and he wanted to clean out his case a bit. He took out all of the cables from the system and realized that because of his cable management he couldn't get his power cable. Not a problem, he took the cable from the back of an older LCD monitor and plugged it in the back of the PSU. Once he was done cleaning he turned it on and it got power but we didn't hear any beeps from it post'ing. He then put the case back and plugged in all the original cables and still nothing, no post, no beeps, nothing.

You guys think he fried the PSU?
 
Their is an easy way to tell.

Open up the PC
remove the power connectors from all the devices (Mainboard, hdd, cdrom, everything)

Now, plugin the PSU
Make sure the lil switch on the back is on

Grab a paper clip and look @ the 20 or 26 pin connector.

Right in the middle of the connector you'll see green wire, normaly very close to the center and surrounded by black wires.

Just use a paperclip or bend a staple and short the green wire, and the black wire. The PSU should come on. This isnt %100 sure that its not the PSU but 9/10 its a good indicator that thats not the problem.
 
Something else. If the PSU is ok (and if it seems to power up but not boot it could likely be)
remove all the ram from the system. Power it on. If it just beeps and beeps then its a good sign the board and psu are alright.

Have you tried striping it to barebones?
PSU
Mainboard
CPU
Ram
Video

Remove anything else. Even the keyboard mouse, and other connected equipment.
 
with everything removed from system, just a regular barebones start, nothing beeps. Nada, just wont post.
 
The PSU could be the culprit but if the mobo is powering up and the drives are spinning it's doubtful. Try resetting CMOS using the jumper and see if default settings will get you to pass POST.
 
we've done a few clearings of the cmos, leaving it unplugged, battery out, clearing cmos jumper set. All for more than 12 hours.
 
Something else. If the PSU is ok (and if it seems to power up but not boot it could likely be)
remove all the ram from the system. Power it on. If it just beeps and beeps then its a good sign the board and psu are alright.

Have you tried striping it to barebones?
PSU
Mainboard
CPU
Ram
Video

Remove anything else. Even the keyboard mouse, and other connected equipment.


that's the starting point. the memory removal is key. if you hear the memory error (3 beeps) then your psu is probably fine. if not, you're down to mobo and psu.

start with as few componants as necessary (no sound card, not video - use onboard, etc)

zv
 
we've done a few clearings of the cmos, leaving it unplugged, battery out, clearing cmos jumper set. All for more than 12 hours.

Well i've seen crazier situations, any chance you can test another PSU in the board?

If your geting nothing with the ram removed (and all other perferials)
Then you've narrowed it to 3 possible problems.
PSU
CPU
MainBoard

So your PSU is definatly on the top of the list :)
 
yeah, we've tried running it with no ram in there. No beeps, nothing.

we ran it with the cpu, psu, mobo connected, AND ran it out of the case on some cardboard, in case it was being shorted out.

Still, no post, no beeps.
 
Did you try reseating the CPU? If so, you've gone about as barebones as you can get and I would suggest replacing those three components.
 
Test with a different PSU first ;) I wouldnt just replace everything :)


Sorry, I wasn't too clear. I didn't mean to replace everything at once. Start with the least expensive solution and move up from there. You narrowed it down to three devices, so it shouldn't take a bundle of cash to figure out what the issue is.
 
I'll be running down to CompUSA tomorrow and pick up another PSU, I'll let everyone know what happens.
 
alright, not to resurrect an old thread but I STILL need help with it. I purchased a new PSU and the problem persisted so I got a refund. My new G.Skill RAM came today, and the problem STILL persisted. Three lights come on, meaning it doesn't detect the RAM. The new RAM is good, its been tested in another system.

Do you guys think it could be the DFI board?
 
Back
Top