Flash M1015 to IT firmware?

danswartz

2[H]4U
Joined
Feb 25, 2011
Messages
3,715
So I picked up one of these on ebay. I've been told I don't need to flash the IT firmware, since the disks will be passed thru as JBOD. Unfortunately ESXi 4.1 doesn't like the card and hangs loading the megaraid_sas driver. There is supposedly an updated driver, but I haven't tried that yet. I've seen several posts various places telling me how to use sas2flsh or whatever to flash the IT firmware, but if I do it under DOS on the box that runs ESXi (normally that is), the DOS sasflsh.exe app tells me 'unable to initialize PAL'. I have tried on three different mobos with no joy. If I try under windows, the windows sasflsh.exe app tells me no LSI cards were detected. What makes this frustrating is the (literally) dozens of conflicting and confusing posts on various boards :( Supposedly this can also be done under linux. Any ideas? Thanks!
 
I saw that post. Did you see where I said 'sas2flsh.exe fails due to unable to initialize PAL message?' I am taking the m1015 to work this morning. I'm going to try it in a couple more PCs - maybe I will get lucky. This is really lame, LSI...
 
Did you see where I said 'sas2flsh.exe fails due to unable to initialize PAL message?'

Nope, that is not what you wrote.

If you want help, you need to post a specific step-by-step procedure of what you did and exactly where it went wrong.
 
I guess I am confused here. My OP said "the DOS sasflsh.exe app tells me 'unable to initialize PAL'." How is that 'not what you wrote'? Granted, I should have provided more detail - the problem I was having was trying to understand the half dozen different (and conflicting, and outright wrong) posts on several different sites. To be more specific, I did follow exactly the directions on the site referred to in the 2nd post - twice, sas2flsh failed due to the PAL error (which according to LSI knowledge base, seems to be luck of the draw with mobos.) I finally got this working by trying again on a non-intel mobo (asus) and it works.
 
Okay, I re-read my post for the 4th time. Yes, when I typed in the OP, I entered 'sasflsh.exe', not 'sas2flsh.exe'. I had to type by memory because I couldn't get a screenshot. I will point out that earlier in the same sentence, I typed 'sas2flsh.exe' (the correct name). LSI also seems to have a sasflash.exe, but no sasflsh.exe. I would have assumed that if someone had put sas2flsh.exe and sasflsh.exe in the same sentence, that one of them was a typo, but that's just me I guess...
 
Specific instructions for anyone else wanting to do this:

Follow the instructions here http://lime-technology.com/forum/index.php?topic=12767.15, scroll down to the post from May 22nd 12:30:07AM. It is critical to erase the flash first, otherwise sas2flsh.exe will tell you there are no SAS adapters present (I presume it is looking at the flash and seeing a megaraid firmware, so reports no adapter present.) Then, the next step flashes the IT firmware and BIOS. This is where I got into trouble - the first 3 mobos I ran this on, sas2flsh.exe throws an error message about being unable to initialize the PAL. This is referenced on LSI's knowledge base here http://kb.lsi.com/KnowledgebaseArticle15807.aspx, although I think it may apply to more than just the two chipsets they reference. If you get this error, you need to keep trying mobos until you fine one that works. The 5th one I tried was my ASUS mobo in my windows7 workstation. The final step is to flash the SAS address using the same program (sas2flsh).
 
I would have assumed that if someone had put sas2flsh.exe and sasflsh.exe in the same sentence, that one of them was a typo, but that's just me I guess...

The problem is that computers do not know what you mean, they only know what you type. They cannot read your mind, and neither can we.
 
Sorry to bump an old thread,

But I have 3x of these cards and am getting the same error.

Upon the command "sas2flsh -o -f 2108it.bin -b mptsas2.rom"
I am getting the same Error to initialize PAL.

Now two of my cards have no firmware on them as it erased it fine, however having issues writing it back to the card! I have tried it on my Asrock P67 Extreme 6 mobo as well as my Supermicro X9SCM-F board with no luck...

Is there a workaround or a way to do it from windows 7?

Thanks for any help
 
I had this happen. As I recall, it has to do with the mobo. Need to try different ones until it works :(
 
Eh, does MSI boards work? My asrock or Supermicro server boards are giving same errors... I have a MSI board upstairs, however it only has 1 pciexpress slot which holds the video card! :( no pci video cards layin around anymore..
 
No idea, I tried 3 mobos that didn't work - finally tried my asus w7 box and it worked there.
 
The m1015's are picky with motherboards. I'm currently using one on my asus m4a89td and the card is working fine, but I can't access the card's bios. Sticking the card in a optiplex 745 (my testing/flashing workstation) it loads the bios fine. Strange cards they are. :confused:
 
Actually posting from my server now.

I was able to erase the bios from DOS.

I was able to reflash under UEFI with sas2flash.efi without any issue.

Not sure if its a motherboard problem more than a driver/detection issue in bios? Same board in different setup worked fine.. now I just need to figure out how to configure all the drives in SE11
 
I suspect it's the version of SASFLASH that might be causing problems

That is if someone has time and can check for me....

If you have a board that wouldn't allow the flashing to work

Follow my guide for the SC44Ge card flash process, and download the BR10i version of SASFLASH.
http://forums.overclockers.com.au/showthread.php?t=980841


Try again on the same (not able to flash board) and see if it works with the IBM SASFLASH...

Just a thought;)
.
 
I agree with you, i definately think its something to do with the version of the software. That other one worked fine for me without any issue as I booted to EFI.

Got napp-it running in like 10 min. Doing benchmark on my drives in zfs-z2 now.

My other question is how or where do I reorder the location of my drives to match up to my Norco 4224. It compiled a list of every drive in there, but how does it order them so if one fails I know which one it is? I planned on numbering them from 0-23 but not sure where the settings are to identify ports..
 
If you are in IT mode, the m1015 will present WWW names to the OS, so it's easiest to write those on a sticker per drive or something...
 
You can run this script to get the drive names and the serial numbers. My drives (Hitachi 3TB) already have the serial number on a sicker at the end of the drive...so no need to do anything. But in your case, you could have a lookup table on the side/top of the case.

Code:
#!/usr/bin/bash
/usr/sbin/prtpicl -v | awk '/:inquiry-serial/{s=$2} s!="" && /devfs-path/{print $2, s; s=""}' |sort|tee /tmp/1 >/dev/null 2>&1
cd /dev/dsk; ls -l *p0|awk '{print $NF, $(NF-2)}'|sed 's/.*ices//;s/:q//'|sort |tee /tmp/2 >/dev/null 2>&1
echo "-------------------------------------------------------"
join -o 1.2,2.2 /tmp/2 /tmp/1 |sort
Code:
# ./drive_serial_numbers.sh
-------------------------------------------------------
c0t5000CCA228C1D283d0p0 MJ1311YNG408HA
c0t5000CCA228C1DB52d0p0 MJ1311YNG42M7A
c0t5000CCA228C1DD35d0p0 MJ1311YNG433UA
c0t5000CCA228C1E0D3d0p0 MJ1311YNG442PA
c0t5000CCA228C1EA96d0p0 MJ1311YNG46P9A
c0t5000CCA228C1EB93d0p0 MJ1311YNG46YGA
c0t5000CCA228C1FA5Ad0p0 MJ1311YNG4AWHA
c0t5000CCA228C1FBDEd0p0 MJ1311YNG4B90A
c0t5000CCA228C1FF03d0p0 MJ1311YNG4D3ZA
c0t5000CCA228C20D27d0p0 MJ1311YNG4HWSA
c34t0d0p0 6000c29c345fdfe2a3a3869a12841159

Note the long drive names on the M1015 card (ie. c0t5000CCA228C1D283d0p0).
 
Hey hey favors, can you run the croinfo command with your norco pls?

And post the output

.
 
Back
Top