First Build, Some Questions About ESD, etc.

—§urfÅceЗ

Limp Gawd
Joined
Aug 26, 2005
Messages
266
Hi all. I've enjoyed computers for a while, and last year I decided that it was time I built my own.

So for the past two months I have been collecting parts, and I finished this week when my 8800GT arrived (thanks Newegg). Now I have to put everything together. In the past I have done single-part upgrades, such as sound cards, GPUs, and RAM with only rubber gloves. But this is my first time starting from scratch. Also, I've got the whole wisdom of age thing against me, because I'm a stupid 14-year-old:(.

I have heard a few basic things but I want to verify them all and ask a few of my own questions. My appreciation for truthful, 100% guaranteed-correct answers is totally unaccountable (while it may be a hysterical prank for you, its won't be quite the same for me). Please, please, please be as comprehensive as possible.


  • First, what clothing should I wear? The minimal? Just boxers? No socks?

  • I will be either working on my varnished hardwood floor or my bed, depending on which is safer (the former, yes?).

  • I am pretty sure that a grounding strap for my wrist is essential this time; the nyplex gloves won't be reliable. What is an ideal metal object that I should attach the alligator end to? Should I still wear the gloves anyway?

  • Okay, so we've got the mid-tower ATX case. The Corsair PSU goes it first, right? Do I plug the AC cord into an outlet before putting anything else in? Do I then power it on before putting anything else in, or is that a total no-no? (I have seen some people say its good, but far more say its bad).

  • Is an I/O backplate for the motherboard highly important? I believe it is, but I want to be sure. Does this get installed before the PSU, or after (if after, when)?

  • Should I connect cables (y-splitters, IDE, SATA, MOLEX, etc) immediately after installing the part they are for, or after installing all of the parts? (probably after: it would be easier to put on lock ties)

  • For applying my thermal compound, what should I use as a squeegee?

  • Are there any very good videos around the web of people building PCs?



I'll probably add more questions later as they come to mind.

Thanks
 
Ok, I'll try to answer your questions. First off, it's important to take your time, and if you have any other questions, feel free to post here before you do something if you're unsure. Also I work with computers all the time, but haven't completely built one in about 3 - 4 years, so my methods may be outdated.

* First, what clothing should I wear? The minimal? Just boxers? No socks?

- Just wear normal clothes, no need to strip down to your boxers. :eek: Do wear rubber soled shoes if you will be standing on carpet.

* I will be either working on my varnished hardwood floor or my bed, depending on which is safer (the former, yes?).

- Try to get a nice flat table....I'd imagine it'd be a pain in the butt to be bending over working on the floor. See if you can get like just a decent plastic folding table for $30 bucks, like at WalMart or whatever. But if you have to work on the floor do that. Wood or plastic, something not metal and not your bed, which would build up static charge pretty easily.

* I am pretty sure that a grounding strap for my wrist is essential this time; the nyplex gloves won't be reliable. What is an ideal metal object that I should attach the alligator end to? Should I still wear the gloves anyway?

- I usually attach the clip to just any non painted metal surface of your computer case, or just go without it and be sure to touch a metal object every few seconds. I've never worn gloves when working on computers.

Okay, so we've got the mid-tower ATX case. The Corsair PSU goes it first, right? Do I plug the AC cord into an outlet before putting anything else in? Do I then power it on before putting anything else in, or is that a total no-no? (I have seen some people say its good, but far more say its bad).

- Well this is up to you. I usually lay out my parts, then install the RAM, CPU, CPU Heatsink onto the motherboard, and then install the motherboard with all the attached components into the case. Then from there I install my video card, and any other cards, and then the PSU last.

* Is an I/O backplate for the motherboard highly important? I believe it is, but I want to be sure. Does this get installed before the PSU, or after (if after, when)?

- Yes it's important, as most motherboards are each slightly different and have different ports in different places, so you will need that, or you can actually discard it completely, at least I have on a couple computers if looks aren't important to you. You should install it before you install the motherboard, as the motherboard ports will be lining up to the backplate.

* Should I connect cables (y-splitters, IDE, SATA, MOLEX, etc) immediately after installing the part they are for, or after installing all of the parts? (probably after: it would be easier to put on lock ties)

- Doesn't really matter, you can do one at a time, or all at once, it's usually easier I think to install cables after all parts are installed, then you can figure out the best way to route the cables.

* For applying my thermal compound, what should I use as a squeegee?

- This is where I'm probably a little outdated, but I always just put a little drop on, like a drop of water size right in the middle of the CPU, and then when installing the heatsink, if you do it correctly it should apply an even pressure to the compound and spread it for you.

* Are there any very good videos around the web of people building PCs?

- Here's one I found: http://www.daileyint.com/build/
 
Also in regards to your one question:

Okay, so we've got the mid-tower ATX case. The Corsair PSU goes it first, right? Do I plug the AC cord into an outlet before putting anything else in? Do I then power it on before putting anything else in, or is that a total no-no? (I have seen some people say its good, but far more say its bad).

Well at least for me, I don't plug anything in until all parts are assembled. The PSU is installed in the case, but it is not plugged into the wall until the motherboard power connector and all hard drives, CD/DVD drives, video card connectors, etc, are installed. Then when the computer is ready to turn on I then plug it into the wall (be sure the voltage selector is at 120v if you are in USA, or 240v for elsewhere, new power supplies I think don't even have that option but double check to be sure)
 
Also in regards to your one question:

Okay, so we've got the mid-tower ATX case. The Corsair PSU goes it first, right? Do I plug the AC cord into an outlet before putting anything else in? Do I then power it on before putting anything else in, or is that a total no-no? (I have seen some people say its good, but far more say its bad).

Well at least for me, I don't plug anything in until all parts are assembled. The PSU is installed in the case, but it is not plugged into the wall until the motherboard power connector and all hard drives, CD/DVD drives, video card connectors, etc, are installed. Then when the computer is ready to turn on I then plug it into the wall (be sure the voltage selector is at 120v if you are in USA, or 240v for elsewhere, new power supplies I think don't even have that option but double check to be sure)

Installing the PSU and using the case to "ground" yourself without the PSU or anything else actually being connected to GROUND is useless. You need to plug the PSU into the wall, and leave it turned off, if you plan on using the case/psu to ground yourself.

Install the I/O plate before installing the motherboard. Install the CPU, HSF, and RAM onto the motherboard before mounting the motherboard to the case. I usually do a bench test with those parts on my desk, to make sure none of the parts are DOA (along with the vidcard, monitor, kb, and psu plugged in -- no drives -- just see if it POSTs).

You don't need to spread the thermal compound. Just follow the directions on the arctic silver website for AS5.

Here's a guide for first time builders, though its not a video guide: http://www.mechbgon.com/build/index.html
 
Back
Top