Finished my custom reservoir

cerebrex

[H]ard|Gawd
Joined
Sep 29, 2004
Messages
1,571
here is the plans I drew up a few weeks ago:
res_001.png


Here is what it came from, a q-tip holder from the container store.
res_002.png

res_003.png


computer_01.jpg


I had a previous thread, but since hardforum crashes and goes down every 2 days, it lost the thread. Here is the finished product, unfortunately I used the wrong glue and had to cut it and re-glue it once, hence the nasty seam.
 
Pretty cool...

Why did you change the design? In your diagram you have the port in the secondary tank mounted high on the tank, and the finished product is the opposite?

Just curious.. and bummer about the seams.. nice work though.
 
Pretty cool...

Why did you change the design? In your diagram you have the port in the secondary tank mounted high on the tank, and the finished product is the opposite?

Just curious.. and bummer about the seams.. nice work though.

well in the previous thread that no longer exists due to hardforums constant crashing (yes, I still harbor negative feelings regarding its constant instability) I discussed the design with several of the members, and I made changes to it, and it turned out to work just great with the changes. The seams do not look bad at all honestly, you can't even see them, however when I took that picture I had to use my ridiculous 300mm lens (I broke my wide angle) and run a real long exposure to capture the light (I was standing in another room, lol) ... the UV light grabs the air bubbles in the seams and makes them look 10x worse, you cant even see them actually.

I installed a blue LED that fires down across both tanks, and it makes the whole computer flicker like it's underwater since there is quite a bit of turbulence where it aims.. pretty cool unplanned effect.
 
well in the previous thread that no longer exists due to hardforums constant crashing (yes, I still harbor negative feelings regarding its constant instability)

I know.. I lost somewhere around 150-200 posts because of the last rollback, but I look at it like this..... Had it not happened, I wouldn't have seen some of the cool things I that have now due to "re-threads" like this one;)

And the seams don't look all that bad in your pic... Again nice job!
 
I know.. I lost somewhere around 150-200 posts because of the last rollback, but I look at it like this..... Had it not happened, I wouldn't have seen some of the cool things I that have now due to "re-threads" like this one;)

And the seams don't look all that bad in your pic... Again nice job!

thanks man! It was a lot of hard work, but I learned a whole hell of a lot about acrylic doing it, that was the most important part. When I get my wide angle lens back, I'll take some more shots so you can see it clearer. I also made some custom mounts for it to fit in the case.
 
Nice work and good idea! I know the seams bother you, but to us it not that noticeable. I like how it's designed to catch those damned air bubbles we all have issues with.
 
I hope they don;t leak . But good job.

heh, well I have a spare loop that I test my WC setups with, I ran it for a week, I did find 3 leaks initially, which I fixed.

If I were to attempt this again, I could probably make it look 100x better 10x quicker.

It's a fun project. I toyed with the idea of making the connecting line out of some soldered copper pipe, but the fittings are pricey, and it would have been complicated to do.... but I could certainly have done it, the threads are much, much larger than what I used on this though, increasing the chance of a crack when you tap the hole.

All in all it's original. Unfortunately my case is crammed all to hell with equipment. Theres practically no air space in that thing that doesnt have a piece of hardware or a line. I had to remove a support for my 250mm fan, and cut a notch in the shroud to get it to fit flush closed with the new res there. Believe it or not, this mid tower weighs over 100lbs.
 
Back
Top