fairly new computer won't power on

ohwell26

n00b
Joined
Dec 20, 2007
Messages
11
Hey, I've got a bit of a problem. I've recently built a new computer (about a month ago) and it has worked fine... until now. Basically, I woke up this morning and pressed the power button and nothing is happening. The fans don't turn on (they are attached directly to PSU btw), PSU doesnt turn on, nothing turns on, however there is a green LED on the mobo which turns on as normal. I've checked all cables and they are working fine... no idea what to do now.

Before you ask, I DID jump start the PSU, and it DOES turn on that way (and all the fans go on etc), but it just doesn't work when I plug it into the motherboard and press the case power button.

Thoughts?
 
Did you try it without the case pwr button, by just shorting the two power leads on the mobo?

If that doesnt work, something may be shorting the system out. To test this theory, you'll have to remove everything from the case.

/*------------- <cut n paste> -------------*/
If you have both the 20/24 pin main ATX connector plugged in, AND the 4-Pin (or 8-pin) ATX12V P4 CPU connector plugged in, then the board should boot fine (unless it requires more power connectors from the PSU). You could try clearing the CMOS.

Setup everything outside of the case, with the mobo on top of its cardboard box. Plug in only the essentials:
- PSU (namely: main 20/24-pin ATX connector and 4-pin ATX12V P4 CPU Connector)
- CPU w/ HSF
- Single stick of ram
- Videocard if there is no onboard video (along with its power connector, if it has one)
- Monitor
- Keyboard
- System speaker/buzzer

* Use a screwdriver if your board doesnt have an onboard power switch. Jump the two power switch leads to turn the power on.

If it won't post, try different RAM slots. If it still won't post, pull out the ram (so no ram in the system) and listen for error beeps. If none, pull the vidcard and listen for error beeps. If none, re-seat the CPU and HSF, then try again. Report back with results if you're still having issues.
/*------------- </cut n paste> -------------*/
 
By shorting out the two power leads you mean just connecting the two metal things where the power button cord would usually go, by touching them both with a screwdriver? I tried that, nothing happened.

I'll try setting everything up on some cardboard later, but I don't see how something would be shorting out if it was working perfectly last night and I didn't do anything to it.
 
Yah, hold the screwdriver or whatever metal you're using there long enough for the system to power on.
 
This is my exact problem with my shuttle SN95G5, but that system is years old... But every once and while I get lucky and it boots for a millisecond and then shuts back off, will take it all apart and try reseating everything. Pain in the ass with a shuttle
 
Okay well if my problem is similar, I tried everything suggested in the copy/paste and it still doesnt boot. the computer is elevated, off of a glass top desk under all the components is brown paper bag, the components are spread out, everything is connected. I'm calling around to see if anyone around has a good PSU that I can try to use.
 
This is my exact problem with my shuttle SN95G5, but that system is years old... But every once and while I get lucky and it boots for a millisecond and then shuts back off, will take it all apart and try reseating everything. Pain in the ass with a shuttle

With my friends shuttle, there was a metalic ribbon cable that connected the front panel with the board. This metalic ribbon would short out the system when it came in contact with the RAM heatspreaders. I'm not sure if this is the same thing happenning in your case, but its something worth checking out.

Okay well if my problem is similar, I tried everything suggested in the copy/paste and it still doesnt boot. the computer is elevated, off of a glass top desk under all the components is brown paper bag, the components are spread out, everything is connected. I'm calling around to see if anyone around has a good PSU that I can try to use.

Yah, try another PSU if you could.

What are your parts?
 
Its disconnected.

I just bought a new PSU, good to go. Except the facking fact that the mATX mobo wont fit into a standard case
 
Its disconnected.

I just bought a new PSU, good to go. Except the facking fact that the mATX mobo wont fit into a standard case

Shuttle boxes don't use mATX boards. They use mini-ITX boards, a standard that they basically created, lol. No need for a case, set it up outside of the case. See my post above.

By shorting out the two power leads you mean just connecting the two metal things where the power button cord would usually go, by touching them both with a screwdriver? I tried that, nothing happened.

I'll try setting everything up on some cardboard later, but I don't see how something would be shorting out if it was working perfectly last night and I didn't do anything to it.

Yah, its strange to see something just die out of the blue. The best way to test if its a short, though, is to remove it from the case. Keep us updated.
 
Back
Top