EVGA 780i windows troubleshooting issues...

Andross182

Gawd
Joined
Sep 20, 2005
Messages
527
So I built myself a machine running MS server 2003 R2 x64 and I seem to have some issues...

Current setup:

EVGA 780i 132-CK-NF78-A1 motherboard
Intel Q9300
8 gigs ocz memory
1x 150gb raptor for OS/Virtual Machines
4x 750gb RAID 1+0 array for file share

Here is my problem in a nut shell. Ran a windows update to get the latest fixes mentioned on the front page a few days ago. Rebooted the machine and it booted with a BSOD saying that c:\software was corrupt. I look in my event viewer and see that my nv64gts.dll file is reporting bad sectors on my harddrives. I scan my raid array which came up clean, however the 150gb raptor has some bad sectors (RMA already processed for it).

So trying to run a chkdsk I found a new problem...booting off my server 2003 media, I get a BSOD right after it finishes loading drivers to memory and says "please wait while starting windows". So I checked the memory, running memtest86+ over night which came back with no errors. I have tried pulling 2 sticks out to load it with 4 gigs and it BSODs, I have tried swapping the 2 sticks in for the other 2 sticks and same thing happens. I tried disconnecting all HDDs from the system and booting and it still BSODs. I have even tried different server 2003 media and it BSODs. This is the kicker, I put my Windows Vista disk in and it boots into its installer just fine...

anyone else got any ideas?

*edit* just tried xp media, still BSOD
***STOP: 0x0000007B (0XF78D663C, 0xC0000034, 0x00000000, 0x00000000)
 
Weird... I remember having troubles installing windows with 4 gigs of ram installed, but if I reduced it to 2 gigs it installed just fine. :(
 
http://www.newegg.com/Product/Product.aspx?Item=N82E16820227290

thats the memory kit that is in the system now. When I installed server 2003 I installed it with all 8 gigs the first time...:(

Heres a question...there is a BIOS update out for the board...however it is saying you need to default the bios after you update. Being that I am using the onboard raid controller, will it blow my defined raid settings away and set all the ports back to not being enabled for the raid? Or are they exempt from the default settings?
 
http://www.newegg.com/Product/Product.aspx?Item=N82E16820227290

thats the memory kit that is in the system now. When I installed server 2003 I installed it with all 8 gigs the first time...:(

Heres a question...there is a BIOS update out for the board...however it is saying you need to default the bios after you update. Being that I am using the onboard raid controller, will it blow my defined raid settings away and set all the ports back to not being enabled for the raid? Or are they exempt from the default settings?
I don't know. I know one of the reasons they want you to set the settings to default is to make sure you aren't OCing to high and you get brick when your OC isn't stable as you update.
 
Weird... I remember having troubles installing windows with 4 gigs of ram installed, but if I reduced it to 2 gigs it installed just fine. :(

Are you using Windows Vista? If you are I would suggest taking a look at this. I wasn't able to install more than 3gb on my EVGA 780i until I ran this patch. Now I am running 8gb with no issues. You are probably seeing something similar to this when you run more than 3gb of ram before the patch:
STOP 0x0000000A (parameter1, parameter2, parameter3, parameter4)
IRQL_NOT_LESS_OR_EQUAL
 
Are you using Windows Vista? If you are I would suggest taking a look at this. I wasn't able to install more than 3gb on my EVGA 780i until I ran this patch. Now I am running 8gb with no issues. You are probably seeing something similar to this when you run more than 3gb of ram before the patch:
STOP 0x0000000A (parameter1, parameter2, parameter3, parameter4)
IRQL_NOT_LESS_OR_EQUAL

I don't remember, I think it was when I installed vista64. I just took a stick out and tried again. From the error message it was clear I had "rolled over".
 
Correct, there is an issue with Windows Vista x64 installations that are not properly reading 4gb of ram or more. I had to install my Vista Ultimate x64 with just a single 2gb module, then apply the patch. Update for Windows Vista for x64-based Systems (KB929777) fixes an issue in storport.sys which results in a system crash when certain hardware configurations exist. This problem occurs if the following conditions are true:
• The computer uses more than 3 GB of RAM.
• The computer uses a storage system that is running the Storport miniport driver.
• The computer uses a controller that uses 32-bit direct memory access (DMA).

If you are still having issues with using 4gb of ram I would suggest getting the update. I was still having issues after getting SP1 but had none after applying that specific update.
 
That update is now included in SP1 of Vista, so just get new media and your problem should go away...anyone got any ideas regarding my issue? (yes im thread jacking my own thread)
 
Hmmmm, I can't think of anything at the moment. There was an issue with using USB drives to load the software though if I remember correctly.
 
I have that same board and after windows updates, I found the only nforce package I could run without bsod at same spot as you was v.15.25
if that doesn't work, I'd say the only thing to do is an OS re-install -in the past when I've overclocked mem to far, my drives appeared to be bad, when it was only that the mem corrupted files -since your showing corrupted files, I'd say re-install is your only option -(bad mem will cause the same symptoms) -and try reinstall with just ONE stick of memory -to narrow down the problem
 
I have that same board and after windows updates, I found the only nforce package I could run without bsod at same spot as you was v.15.25
if that doesn't work, I'd say the only thing to do is an OS re-install -in the past when I've overclocked mem to far, my drives appeared to be bad, when it was only that the mem corrupted files -since your showing corrupted files, I'd say re-install is your only option -(bad mem will cause the same symptoms) -and try reinstall with just ONE stick of memory -to narrow down the problem

You realize this thread is over a year old right?
 
You realize this thread is over a year old right?

no, I didn't thanx -usually look at that -missed it this time -might still help somebody though -wish he would have finished this thread with what he ended up doing
 
Back
Top