eVGA 680i HSF compatibility...

buffbiff21

Gawd
Joined
Sep 27, 2006
Messages
1,014
I know many have noticed that HUGE heatsink on the motherboard.

My question is, does anyone have a clue what HSFs will fit on the board?

I have a thermaltake Blue orb, and its HUGE... dont think it will fit over that big sink on the mobo.

I want the 680i real bad, but i think ill have to buy another cpu fan...

(oh... waiting and then spending 400 for the ASUS board is not really an option :eek: )
 
The heatsink on the 680i for the demo was a zalman 9500 the was plated with nickel
 
Your bigger problem with the EVGA is not what fits on the board, but what fits in your case. That heatsink mount is right at the top edge of the board, and if your case has the power supply next to the motherboard, you'd better stick with a compact HSF.
 
I have a Scythe Infinity mounted on mine. If you orient it so that it's blowing across and out the back the fins rest on the fins of the chipset heatsink, but it does fit.
 
the evga 680i has resisters (or something) on the back of the board that get in the way for the zaleman9500 ( i have both). I used a pair wire cutters to hack away at the parts that were touching the backplate, worked fine, just not pretty.


Just a fyi.
 
These electronics also get in the way of the Scythe Ninja backplate which is, I believe, steel. Drilling/dremeling required.
 
Zalman 9700 fits perfectly. It pulls the hot air off the chipset fan and blows it out of the case too. Keeps my E6600 nice and cool.
 
AppaYipYip said:
Zalman 9700 fits perfectly. It pulls the hot air off the chipset fan and blows it out of the case too. Keeps my E6600 nice and cool.
Did you have a problem with the backplate ???
 
I did not have a problem. I don't know what others are talking about in regards to the backplate issue.
 
i am running the 9500 (the AMD model with the nickel plating - but using the Intel model's mounting hardware.)

I just put the plate on the back as usual. It did run over some of the solder points, but it does not seem to ba a problem at all. OC'd my 6700 to 3.5 with zero issues so far. Plays games VERY well.

I get my 8800GTX tomorrow... cannot wait!
 
darkjedi said:
i am running the 9500 (the AMD model with the nickel plating - but using the Intel model's mounting hardware.)

Good to know it works, thanks! Got the same for my A64 3700+ and was wondering if it'd be a problem with a 680i board and C2D. :)

Thanks.
 
I just installed the backplate for the 9700, but it is resting on one of the resisters, It doesn't lay flat on the board, only on one side of the backplate though. Will this be ok ???
 
SKL1 said:
I just installed the backplate for the 9700, but it is resting on one of the resisters, It doesn't lay flat on the board, only on one side of the backplate though. Will this be ok ???
I wouldn't trust that. You might crush the resistor and kill the board. Better to Dremel out the backplate rather than risk a $300 board.
 
Yeah, I plan on doing that to mine. I am going to take some pictures of the process and will make a post here to show anyone where to cut and whatnot. A little guide of sorts.
 
kraken0698 said:
Yeah, I plan on doing that to mine. I am going to take some pictures of the process and will make a post here to show anyone where to cut and whatnot. A little guide of sorts.
Thread over at EVGA Forums.
 
Hey..anyone of you guys using the Thermalright Ultra-120..I just got it from svc.com..they had it on sale for $39.99..which is a good deal to me..and I'm also looking to get the evga/xfx/BFG motherboard and wanted to know if anyone has this heat sink ..any problems?
I was told if it didn't fit I could return it..but I want this cooler for my new build..anybody??

thanks in Advance .. :D
 
Darkside said:
Hey..anyone of you guys using the Thermalright Ultra-120..I just got it from svc.com..they had it on sale for $39.99..which is a good deal to me..and I'm also looking to get the evga/xfx/BFG motherboard and wanted to know if anyone has this heat sink ..any problems?
I was told if it didn't fit I could return it..but I want this cooler for my new build..anybody??

thanks in Advance .. :D
Looks like the Ultra-120 is a no go on the evga 680i board: http://www.hardforum.com/showpost.php?p=1030212513&postcount=55
 
so has anyone got a tuniq tower on the 680i? i thought the ultra 120 and the tuniq had similar backplates.
 
Damnit, now I have to get a new heat sink and fan assembly for my eVGA 680i board.
 
Back
Top