Did I just break my computer?

Joined
Aug 20, 2002
Messages
657
I was getting ready to do a reformat, and shut down my computer. Without taking out the power cord, I opened the side of my case and unplugged the SATA connector from my 2 secondary HDDs, so the formatee would receive the correct drive letter.

After closing the case and pressing the power button, nothing happens. The mobo indicator light is green, but there is literally no response from anything. Turning the system off results in the power supply discharging sound after a few seconds.

Does it sound like I fried my motherboard or psu, even though they're still apparently alive? What could've happened?
 
I've done that before. In fact I just did it this afternoon when I upgraded my RAM and CPU cooler. Got the same nothing until I reset the CMOS, then everything was OK. That would be worth a try.
 
Interesting...I plugged the PSU into another system, and it booted up fine.

Is the mobo dead despite the green indicator?
 
Jimmy the Greek said:
Is the mobo dead despite the green indicator?

No, it's most likely fine. SATA drives are supposedly hot swappable, so unplugging them should not have caused any problems, but you never know.

I would also recommend clearing the CMOS, I think that should solve your problems.
 
digital_exhaust said:
No, it's most likely fine. SATA drives are supposedly hot swappable, so unplugging them should not have caused any problems, but you never know.

I would also recommend clearing the CMOS, I think that should solve your problems.

Clearing the CMOS didn't work. The board must be dead.
 
Jimmy the Greek said:
Clearing the CMOS didn't work. The board must be dead.
lol jumping the gun a little too quickly aren't we. do a little more investigative work. Maybe someone else came loose.
 
relax....maybe you accidentally pulled the jumper for the power button....I've done that 50 times.....

go make sure the jumper for the power button is still connected to the mobo and on the right pins.......
 
hungryduck said:
relax....maybe you accidentally pulled the jumper for the power button....I've done that 50 times.....

go make sure the jumper for the power button is still connected to the mobo and on the right pins.......

After removing the PSU from my case to test it with other systems, I've put it back in and rewired everything from scratch, including the elusive power switch. Still no luck. Maybe the board is having a bad day.

Well, if I learned anything through this ordeal, it's that it's pronounced "A-Soos" (thanks, Asus tech support.) For so many years, I've been calling it "A-Suhs".
 
If your taking the mobo out, Id give it one last try with just a stick of ram, the psu, and the vid card. It may work and then you can just rebuild it one part of a time, If not then you know its busted for sure, and can pull all the jumpers off and toss it (thought i would hold onto it untill you get another mobo if thats what your doing, so if that one doesnt work either then you know its something other than the mobo and can work from there)

good luck
 
I've tried the RAM, video card, etc tricks but nothing worked. I'm beginning to think my CPU was fried.

When I last shut the computer down (back when it still powered on), I did it just before the POST screen. A8N-SLI does a strange thing with the processor fan before startup (it's quiet, then revs up a few times before starting for good), and I have a feeling that interrupting this process shorted the CPU.

Tomorrow, I'm going to swap the processor into my other S939 board. But before that, I'll make sure that the QFP (or whatever they call it) isn't a shade of brown.
 
Apparently my A8N-SLI Premium has some issues with my Antec Sonata II's PSU. Could this be it? And does it have anything to do with NeoHE?

I just might stop by RadioShack and pick up that $89 Thermaltake.

Update: Bingo! I swapped the Sonata's PSU with an old Antec 430W, and it came back to life.
 
Back
Top