Cutting PCIe 16x down to 8x?

Bladestorm

[H]ard|Gawd
Joined
Dec 10, 2006
Messages
1,232
I have a Dell Poweredge server with two 8x PCIe slots. Short of buying an expensive 1x video card, I was wondering if it would be possible to either trim the connectors on a 16x card down to 8x, or cut the end of off the 8x slot so I can fit a 16x card?

I know an 8x to 16x "wearout extender" exists, but I can't see how doing what I propose is any different than what the extender does.

Thanks
 
I'm pretty sure you can, but I'm not positive. I know you can tape over the ends of the pins and it works, and this amounts to basically the same thing, so I don't see any reason it wouldn't work...
 
You can do this assuming you have an adapter which physically will let it plug in.

The link will only be negotiated on the lanes where a receiver is detected.
 
You can do this assuming you have an adapter which physically will let it plug in.

The link will only be negotiated on the lanes where a receiver is detected.

What do you mean by "adapter"? Are you talking about the "wearout extender"?
 
Pretty sure you can just trim a little spot off the video card or cut a slit in the back of the actual PCIe slot for the video card to fit through (the rest of the card will continue past the slot).
 
I would suggest cutting a notch in the PCIe slot at the end. Much easier than hacking up the video card.
 
Well, I need a new riser card now. I wrecked it trying to open the end of the x8 slot with a Dremel. :( This is becoming more pain than it's worth. I already bought the x16 video card, now I have to spend another $30 for a new riser. I can't afford to keep ruining risers.
 
I guess there isn't any video cards that would fit in an 8X slot? I am pretty much in the same predicament with many of my motherboards that have these types of connectors, which are near useless. :rolleyes:
 
^ A little steep, but that's exactly what I was looking for. Thanks.
 
There's been a few people that opened up the end of and x4 or x8 slot to have a video card fit. I even had a motherboard that came with the end of the x4 slot opened. When I put my x16 video card in it, it worked.

However, a dremel tool (or any other power tool) probably isn't the best thing to be cutting the end of a slot open with. Try something a little more low tech, like side cutters or tin snips. Then carefully use a file to open it up a bit enough for teh card to fit.
 
Yeah, sorry for the delayed response. I believe you can also get them in x4 and x8 depending on what your target lane width is.
 
Wouldn't those adapter raise up the video card so that you wouldn't be able to secure them to the back?
 
Wouldn't those adapter raise up the video card so that you wouldn't be able to secure them to the back?
I'd imagine they would, but anyone motivated enough to spend ~$40 on an adapter that might or might not work would either have little concern or already figured out a solution to that problem. I think I'd try making an opening in my connector first before spending that much on an adapter and not knowing if it will work as advertised. It's too expensive when the cost of a card I'd use would be around $100, effectively adding 40% to the overall cost.
 
I only spent $17 on the video card. It's just a Geforce 6200 LE. I wont be using it to play games or anything like that, but I need something better than the on-board video.
 
you should have just gone with a pci variant then, a 6200 le isnt much better then onboard.
 
I don't know about anyone else, but I've had a lot of bad luck recently when trying to use PCI video cards in newer systems. The next-to-last time I tried it, the signal quality was terrible, full of interference. Then more recently, it was a cheapo Vista system with integrated video and the mobo would not recognize a PCI video card properly and disable the onboard chip--I had to order a PCI-E X1 card for the lone X1 slot on the motherboard, which thankfully worked just fine, and there were only a couple of HiS X1550 cards out there for sale. It just seems like the good old PCI fallback option is getting squeezed out by mobos that no longer support even that much, and budget PCI-E X1 cards haven't multiplied the way they were supposed to.
 
Back
Top