• Some users have recently had their accounts hijacked. It seems that the now defunct EVGA forums might have compromised your password there and seems many are using the same PW here. We would suggest you UPDATE YOUR PASSWORD and TURN ON 2FA for your account here to further secure it. None of the compromised accounts had 2FA turned on.
    Once you have enabled 2FA, your account will be updated soon to show a badge, letting other members know that you use 2FA to protect your account. This should be beneficial for everyone that uses FSFT.

Custom Micro Case

Picture of front of case with both sheet metal and wire mesh in place
MVC-015S.JPG


With this picture you see the radiator , fans in place
MVC-016S.JPG
 
Very nice, about how big is that case? Comparable to the Qpack, Silverstone or is it more like the size of a Fragbox?
 
aznpxdd said:
Very nice, about how big is that case? Comparable to the Qpack, Silverstone or is it more like the size of a Fragbox?
Click to expand...

7 3/4 tall
10 1/2 wide
14 deep


hugs

Jen
 
osk.ocelot said:
what type of metal is that? Nice welds.
Click to expand...

found this at a local flea market , its common use is for security screen doors. you can find similar or same at mcmaster.com


hugs

Jen
 
Looks very cool. :) For some reason it kind of reminded me of something like an Aria/Qpack.
 
CrimandEvil said:
Looks very cool. :) For some reason it kind of reminded me of something like an Aria/Qpack.
Click to expand...

smaller than the Qpack , closer to the size of Aria .

will have new pictures tomorrow. at this time the case is in primer and half painted


hugs


Jen
 
MikeyB said:
What material are you building the frame out of?
Click to expand...

1/2 x 1/2 x 1/8 angle iron is used to make the frame

18 gauge galvanized sheet metal is used for rest


hugs

Jen
 
aznpxdd said:
Nice..I was wondering how you're going to do the power and reset buttons?
Click to expand...

lower left hand corner i have two holes drilled for power and reset switchs.

am adding sound deadening foam to the inside of case , will have more pictures when i have more of this case together


hugs

Jen
 
MikeyB said:
No doubt. This is a sweet rig.
Click to expand...


thank you

am enjoying this new case , so much smaller than my previous case.


hugs


Jen
 
osk.ocelot said:
where did you mount the pump? awesome job BTW
Click to expand...


mounted pump under the powersupply , above the northbridge . made a special bracket that bolts to the back of case .


hugs

Jen
 
i call this revision 2 of the case ,

made the case 7/8 inch deeper so i could move radiator

added two more 80mm fans

moved power and reset switch cause i didnt have room in front anymore

moveing hard drives under the optical drive , with fans blowing through this should allow them to be cool.

now i need some low decibal 80mm fans

MVC-001S.JPG

MVC-002S.JPG

MVC-003S.JPG
 
sabrewolf732 said:
build and sell them :p
Click to expand...

i have my micro cube case for sale on another forum. havent been much interest in it . its a little bigger than this one

jmroberts70 said:
Fantastic work!
Click to expand...

i have case painted again , need to make a new hard drive cage for the case . waiting on the DFI matx board to arrive so i can start placeing everything back in to the case


hugs

Jen
 
Jen said:
i have my micro cube case for sale on another forum. havent been much interest in it . its a little bigger than this one



i have case painted again , need to make a new hard drive cage for the case . waiting on the DFI matx board to arrive so i can start placeing everything back in to the case


hugs

Jen
Click to expand...

Link?
 
Did you design the case before buying the mobo? Or did you design the case around rhe mobo? :confused:

How did you get those epansion slot openings and fan openings? From other pc's?
 
J_I_M_B_O said:
Did you design the case before buying the mobo? Or did you design the case around rhe mobo? :confused:

How did you get those epansion slot openings and fan openings? From other pc's?
Click to expand...


i designed the case with motherboard i have here . the idea was to make a case smaller than my previous case before. i found out i positioned the drives in a area where they would be to hot . since then i have made changes so that the hard drives will be cooled by fans.

the only item i use from other computers is the motherboard tray and atx backport plate. the metal i purchase locally to me. the fan openings behind the mesh was cut with a dremal . the mesh is something i have had here for some time .

hugs

Jen
 
You must log in or register to reply here.
Back
Top