CPU HSF blowing on video card

veritas7

Gawd
Joined
Nov 7, 2007
Messages
736
Due to the awkward angle of my Lian Li case, I have a limited choice for a heatsink fan.

For my HSF, I chose a Thermaltake V1.

However, the measurements were off (the W and L were switched around) and now instead of the HS fan blowing away from the intake part of my case (and towards the front of the case, near the optical area) it is now blowing up and towards my backside of my 8800GT.

TL;dr: Will this heated air towards the back of my 8800GT hurt it?


I am planning to install my Accelero S1 on my 8800GT once everything else is set up
 
It would make keeping the video card cool tough.
Have you thought of ducting the CPU's exhaust to the case exhaust fan?
 
However, the measurements were off (the W and L were switched around) and now instead of the HS fan blowing away from the intake part of my case (and towards the front of the case, near the optical area) it is now blowing up and towards my backside of my 8800GT.

So flip it so its blowing away from your videocard..
 
A flexible hose, plastic like either a clothes dryer uses but smaller diameter to fit over the top of your heatsink and attach to your case exhaust fan.

An Automotive store might have a hose used for intake on a engine the needed size also.
 
I'll take a pic of what I got with my crappy camera phone, but I think my best solution is to find a HSF that will fit... Bah, Lian Li case is perfect except for the divider being so close to the CPU portion of the mobo... :(

here it is, what space i have to work with.



case fan next to it is intake, i guess i can mod it to be out, ill just need somehow to mod then the front unused optical bays somehow to accomodate a fan, as ive seen in some others builds with mesh in front... how does one go upon that?

also, if anyone has any hsf that they think might fit and spit the air towards the front of the case (<-- this way in relative to the pic), seeing that the width of my current HSF is 92mm, and I got about a little over a cm on that divider side still to take, so I might say 120mm is the cutoff.

edit: i see that perhaps the arctic cooling freezer 7 pro might fight the way i want it... is it a somewhat small hsf? looks like its cheap and i can bet on it to hopefully fit... ive already spent 90$ or so on HSF that don't fit the way i want too, argh ! ><
 
If you reverse that case fan and use it as a exhaust, (just flip it) it would help exhaust some the CPU's heat before it can rise up to your GT.
 
Is there anyway you can just reverse the fan? Maybe like cut the wires and switch em so it spins the other way.
 
Although the heat from your CPU is in fact heating up your video card, this is the proper airflow direction for this case. Air enters at the rear, goes over the CPU, then the addon cards, and out the side. That's how the V-series works.
 
As I mentioned above, you can just flip the heat sink fan. Unmount it and rotate it 180 degrees and remount it.... not that hard.
 
As I mentioned above, you can just flip the heat sink fan. Unmount it and rotate it 180 degrees and remount it.... not that hard.

That means it will be blowing towards the divider... isn't that going to screw up the airflow?

Do you think I should do that, make the intake fan to blow out, and then add anoter intake fan to the front (optical bay area)?
 
Worth trying. It's only 4 screws. :D
Check your temps both while surfing and gaming. Reverse the fan and check temps again idle/loaded.
 
The air coming out that CPU fan is probably going to be a lot cooler than the inferno coming from the GT, so I would say its probably helping the GT.

What you need is some sort of extraction fan or slot cooler on the "Fan" side of the GT which is where the GPU builds up its heat, especially the GT as it vents inside the case.

In my opinion you are focusing of the wrong issue.
 
The air coming out that CPU fan is probably going to be a lot cooler than the inferno coming from the GT, so I would say its probably helping the GT.

What you need is some sort of extraction fan or slot cooler on the "Fan" side of the GT which is where the GPU builds up its heat, especially the GT as it vents inside the case.

In my opinion you are focusing of the wrong issue.

There's a fan overhead the PCI slots that exhausts the air from that area/top out of the side of the case.

I'll guess I'll be monitoring different ways of using the case fan and the HSF and seeing if the temps are fine enough - however I don't know how it will be like in the summer or spring as it is cold as heck where I am D:
 
Ghetto fix: Cut up a plastic 2 liter bottle. First remove the sticker, then you will need to cut it vertically in half and remove the top and bottom portions so you have your self a nice ) shaped thing . Now tape this to the side of your exhaust fan to the right of your HSF in the picture, at a angle like \ so it will deflect the air around your GPU.
 
Back
Top