computer won't boot unless I restart twice

DReborn

Limp Gawd
Joined
Aug 11, 2004
Messages
364
ok, weird prob that just cropped up. i am using the system in my sig (a8n-32, opty 175, 2gb pc4000 ocz, 150gc raptor) and just recently when i restart the computer, it won't boot. it will just hang on the mobo logo screen. i hit the restart button (again) and boom fires right up. why?

i tried to go into the bios but then it stalls while it is loading my usb drives on my printer. im thinking that for some reason these usb drives are stalling the reboot but why would it work if i restart again? doesn't seem to make sense. ESPECIALLY since the problem just started when it was working fine before.

no OC'ing btw...everything is stock/default.
 
just to be clear, no hardware/software changes were made...everything was plugged in exactly how it was before but now it just takes two restarts to get it going. can't understand why another restart will work WITHOUT FAIL. It's not like sometimes it takes 2 or 3 or 4...it is always 2 times. Can't imagine what it fixes with the restart.

thanks!
 
This happens to me once in a while with an Asus + P4 630 system and it is a BIOS issue - as far as I know. Try playing with BIOS settings.
 
Sounds like you have a cold sodder on some part. It takes 2 restarts to get it warm enough to work. But are you booting it up from being off? Or just restarting? Because if you are just restarting even if you do have a cold sodder it should be warm enough to work.
 
Abyss of Borg said:
Sounds like you have a cold sodder on some part. It takes 2 restarts to get it warm enough to work. But are you booting it up from being off? Or just restarting? Because if you are just restarting even if you do have a cold sodder it should be warm enough to work.

It's "solder," which doesn't work that way, BTW. Solder is a tin-lead alloy that melts at a certain temperature and is used to create bridges in certain electriconic components. There are hundreds of solder contacts all over inside a computer: on the mobo, vid card, in the case, in the PSU, even in the disk drives. But what solder does is make a direct connection with each component it is in contact with by making a eutectic mixture between the solder bridge and the contacts on the electronic components. In bad soldering jobs, the solder might not be making a complete connection and therefore the pathway is disrupted. So, you'd think just warming up the solder would work, right? Wrong, the only way warming up the solder would effect its conducting ability is if it allowed for the solder to melt in such a way that the connection is reseated and the circuit is completed (or at least augmented to work completely). However, for that to happen with Sn60 solder (the type typically used in electronics), a temperature of 372 F would have to be obtained! Ah! That's a hot case!! Even then, after being reseated once, the problem would go away.

Now, the solder joint COULD be flaky... as in, it partially makes a connection. Sometimes it works, sometimes it doesn't. If that's the case, grabbing a soldering iron and reseating the connection (if the connection causing the problem is ever found) would do the trick.

I don't know what the OP's problem is, but it probably ain't solder. It could be a PSU going south... :( Or worse, a mobo going south.
 
well this is a brand new system so i hope it's not the mobo (a8n32-sli) or the PS (Seasonic S-12 600)! =)

i feel it's bios related too...I am going to reset to default and see if it fixes the problem.
 
you may also want to see if there are any BIOS updates on the manufacturer's website, and flash it to the latest one.....can work wonders sometimes.....
 
I had a similar problem with a KT7E system some time back.. Replacing the PS fixed it.
 
as weird as this sounds, i think it might be the printer and it's built in media card reader. i switched the usb port it was plugged into right before I started having these problems. but i still dont understand how that could possibly trigger this result.

i will first obviously just boot up the computer with just the keyboard mouse and see if it fixes the problem

thanks for all the help, guys. love the hardforum. =)
 
Back
Top