computer used to boot up, but doesn't anymore

Vinin

n00b
Joined
Jul 5, 2006
Messages
3
So I recently came back from college in New Orleans where I had my computer that I built there running fine. When I get back here to New Jersey however, I plug everything in and when I try to turn it on, it starts up a little and then shuts itself off. I had shipped my computer from NO and had opened it up to check out everything inside. Everything seemed fine, but it still wouldn't stay on. All my fans lit up and everything starts whirring, but then it all just stops after a second, or if I am lucky, it will stop after 15 seconds. My first guess at this would be that the power supply was wrong, so I switched that out, and I am still getting the same problem. If anyone could help me out, that would be great. I will list my specs below.

Note: The computer worked fine in New Orleans using the old PSU.

ASUS A8N-SLI Deluxe Socket 939 Motherboard NVIDIA nForce4 SLI ATX AMD
eVGA 256-P2-N383-BX Geforce 6800 256MB DDR PCI Express x16 Video Card (x2) [SLI] (this isn't even listed anymore, they are just vanilla 6800's)
AMD Athlon 64 3000+ Venice 2000MHz HT Socket 939 Processor Model ADA3000BPBOX
CORSAIR ValueSelect 1GB (2 x 512MB) 184-Pin DDR SDRAM DDR 400 (PC 3200) Unbuffered Dual Channel Kit System Memory Model VS1GBKIT400
NEC DVD Burner Black IDE/ATAPI Model ND-3540A
Western Digital Caviar SE WD2000JS 200GB 7200 RPM SATA 3.0Gb/s Hard Drive (x3 more or less, I have three different HD, but unless they have different power draws, it shouldn't really matter that much)
Antec Performance I P180


Old powersupply
Thermaltake Silent PurePower TT-420AD(DUAL FAN) ATX 420W Power Supply

New Powersupply
Antec TRUEPOWERII TPII-480 BLUE ATX12V 480W Power Supply


This is not a review on parts for a machine I will build. I have already built this machine and do not really care for criticisms on the parts. I would just like to figure out why I am having these start up problems.
 
check to make the vid card is seated right, and I'd try some new ram as well.
 
defakto said:
check to make the vid card is seated right, and I'd try some new ram as well.
If the PC booted at all (he said 15 seconds max), then usually ram or video wouldnt be the problem, but you may be correct. Heh, when I had ram not seated right, After checking why my PC wasent booting, I had burn marks on the gold RAM contacts :rolleyes: srtaight to the junk bin

You may have your CPU HS not on right hence the shutdown. It may be CPU or Mobo thermal protection. Take off your heatsink, then remount it, and report back.

Good Luck that seriously sucks for a computer to not to be working like that..I HATE going back to my mom's Slot 1 450MHZ PIII when mine has a problem !!
 
What sucks more is that it has been working for about a year now.
If I am to unseat the CPU, I would have to reapply the thermal paste right?

I have already reseated everything else in the system, still no change. I think "boot" is a bad word. It merely starts to POST, then shuts off with no error message.
 
Well, actually I ment reseat the HSF on the cpu, but while your at it you can reseat the cpu if you feel the need :p .

Actually, yes you'll have to reapply thermal compound, but its good to do that every few years from possible movement of the HSF assembely.

If it starts to POST, then the CPU is still working, but might still be shutting down because of thermal protection preventing the CPU from overheating..because my old AXP 2700+ that fried would make a non-standard beep indicating after I read the manual that the CPU was toast..
 
Well, I'd try our three main suggestions..unless anyone else has another possible solution.

I'm thinking in shipping the Heatsink didnt stay on right. That's common with higher weight sinks, and can even break the mounting clips on the mobo if tossed around too much.
 
Back
Top