Computer randomly restarts...

Bigbeanx

n00b
Joined
Aug 16, 2004
Messages
2
At the moment, I have an Asus A7N8x-E Delux Motherboard, AMD barton 3000+ (400fsb), 1 gig of kingston pc 3200 value ram (2sticks of 512) , and an ATI radion 9600 with 256 megs of ram, and a turtlebeach santa cruz sound card (i know , on board is probably better here), a 350w atx power supply. 120gig maxtor, and a 40 gig seagate baracuda 4, and a cdburner/dvdrom combo.
My problem is, that once i get into windows, my computer randomly restarts itself. Most often when I start an application that will be video card intensive (ut2k4 demo, starting Doom 3), between direct draw tests. Now, i have RMA'd the proc, i've used another board (which with the rest of the same parts, the computer continue's to restart), tested the ram on other computers. Now I used my 1700+ with the pc3200 and the other parts on the current new board, and the computer doesn't restart. So my question is, is this a power supply problem? Do i need more than 350w? or is there a deeper issue. Any help would be great, I'm guessing its either the power supply or ummm computers hate me.
Thanks for reading and any help you can give.
 
I would check:

Your "Value" ram...some motherboards detest the stuff..
Try running the safest or slowest timing available in bios.

How's your cpu temps?
Check the following for overheating or perceived overheating:

- Is the heatsink correctly installed ?
--> Verify it is correctly installed.

- Is the heatsink filled with dust and crud ?
--> Clean with compressed air in a can.

- Is the heatsink fan operating ?
--> Replace defective fan with similar or better unit.

- Is the heatsink adequate for that application/CPU ?
--> Verify it meet the requirements for the CPU being used.
--> RETAIL heatsink? May require lapping and better TIM.

- Is thermal interface material used between heatsink and cpu ?
--> Verify it is used, and is applied according to the manufacturers guidelines.

- Is the TIM pad cover removed from heatsink before installation, if using supplied TIM pad ?
--> Remove the cover before installation, failure to do so will insulate the cpu from the heatsink.

- Is there adequate airflow or case ventialation ?
--> Verify airflow, add case fans if required.

- Is the Vcore set higher than specified by the manufacturer ?
--> Verify the Vcore is set to the manufacturers specification in the mainboards bios.

- Is the temperature read via the internal temperature diode. Is the tremperature read via the socket thermistor ?
--> Temperatures read at the diode can and will be higher than an external reading.

- Is the temperature sensor properly calibrated ?
--> Several board have this problem, check manufacturers bios revision history for calibration fix.

- Outside temperature high ?
--> If the external temperature is high, then the case fans will be drawing in hot air, especially during summer months.


How's the current rating on the 3.3/5/12 volt rails of your power supply and is it a generic supply?

minimum psu specs:

Target output ratings for 300W ATX-12V power supplies in AMD Athlon XP and AMD Duron processor-based systems.
+3.3V = 28A, +5.0V = 30A, +12.0V = 15A->18A
-12V = 0.8A, +5VSB = 2A->2.5A, -5.0V 0.3A

Notes:
1. Maximum continuous total DC output power should not exceed 300 W.
2. Maximum continuous combined load on +3.3 V and +5 V outputs should
not exceed 80 W.
3. Maximum peak total DC output power should not exceed 437 W.
4. Peak power and current must be supported for a minimum of 15 seconds.
5. Maximum current for the 12 V outputs should be 15 A.
6. Peak current for the 12 V outputs should be 18 A.
7. The 5 VSB is only utilized when the system is in S3 (Suspend) mode. Therefore, do not add this load to the total load of the power supply.

Calculate Total Combined Power Used By The SyStem
1. Enter the total current requirements for all the component in the appropriate column.
2. Multiply the voltage by the total current to get the total wattage for each voltage level.
3. Compute the wattage for component power usage, multiply by .8 (to calculate 80% of
the wattage for the devices) and add the wattage requirements of the processor. Always
verify that your power supply is adequate both overall and for the 3.3V and 5V circuits.

For reliable operation, the output of the power supply must be greater than the maximum
total combined wattage usage for the system configuration. In a standard single-user
desktop/tower system, it should be apparent that the maximum wattage usage will be less
than the combined total of all the components in the system. The maximum wattage is less
because it is almost impossible to concurrently use the maximum power of all the
components. Therefore, a power usage factor should be used.
AMD suggests calculating the power supply minimum output capacity as the power
required by the processor plus 80 percent of the total wattage for all the other components in
a desktop/tower systems. This 80 percent value is not a hard and fast value. The system
builder’s in-house testing may change the power-usage factor.
In addition to the overall wattage requirements, the builder must verify that the maximum
voltage for the +5 V and +3.3 V power requirements for the system are less than the wattage
limitation on the power supply for the +5 V and +3.3 V outputs.


Check them over..

Later

MD
 
Back
Top