Computer not starting up... dead motherboard?

Rezn0r

n00b
Joined
Jun 14, 2003
Messages
19
I recently upgraded my computer and planned on using my old motherboard, CPU and RAM to build a computer for my dad, but after switching everything out it doesn't work. The old MOBO, CPU and RAM worked just fine in my old case, then after I took it out and rebuilt my own computer, I started working on my dad's. I turn it on.. the fans spin, but that is all. Nothing on the screen, no beep errors.. nothing.

I know the video card and the RAM are good, so it must be the CPU and/or motherboard. Anyone have any ideas or is my motherboard just dead and there's nothing I can do?

BTW, the old MB and CPU are:
Soyo SY-K7V Dragon Plus! motherboard
AMD XP 1800+ CPU

If anyone has ANY ideas that would be greatly appreciated.
Thanks
 
Check your power supply 110v/220v switch. Reseat the CPU and check for bent pins. Clear the CMOS using the jumper nearest the battery or remove the battery for a few minutes. Try a different power supply.
 
does it boot with no video or does it just sit there?

How do you know the Vid card is good? What is it? In fact, what are the specs of the dead box?

Where did you get the new PSU? Are you sure it is good?

Try taking everything out of the box and booting on a non-conductive surface. That will rule out the possibility of shorts.

/obvious questions
Is the monitor on? Plugged into the vid card? Is the monitor verified good?
 
blackrino9 said:
does it boot with no video or does it just sit there?

How do you know the Vid card is good? What is it? In fact, what are the specs of the dead box?

Where did you get the new PSU? Are you sure it is good?

Try taking everything out of the box and booting on a non-conductive surface. That will rule out the possibility of shorts.

/obvious questions
Is the monitor on? Plugged into the vid card? Is the monitor verified good?

I am currently using the video card in an older computer right now (same with the PSU I am trying) so I know those work. I have tried using my new PSU (In the computer I am using right now; though I haven't tried it recently), and an older PSU that I have (I am pretty sure it works, not 100% positive though). I am using the same monitor that the older computer is on so that works fine.

I also have tried it in a case and not in a case (right now I am using the case for the older PC that is using the old gfx card)

I am trying to run a:
SY-K7V Dragon Plus! motherboard, AMD XP 1800+ CPU, 512 RAM (forget the brand), GeForce 4 MX 440, 15 Maxtor HDD (kind of old, but it works fine), 400W Enermax PSU

When I turn on the computer the fans spin, and the light on the monitor just keeps blinking, nothing else happens.

Thanks
 
try re-seating everything

reset the bios

When you were working on this pc, did you take any sort of ESD precautions?
 
He said that he already tried it outside the case.

did you accidentally bend any pins on the monitor cable when you were working on it?
 
Yeah, i've done all of that.

I didn't really go out of my way to be cautious about ESD but I was careful (though it still could have screwed it up.. you never know). I have built a couple computers in the same place (and they all worked fine), but that doesn't rule out ESD.

Is there any sure way to find out if maybe it was ESD? And if it was what all would be fried? The motherboard and CPU?
 
:: BUMP ::

Anyone have any ideas? And if it was ESD (which I am thinking is the only explanation), am I just completely screwed?

Thanks for the help.
 
If ESD is the culprit then It depends on what was damaged.

It sounds like it may be the MB that is screwed. Do you have another that you can try all the parts on?

Something else to check, make sure all your MB headers are on correctly.
 
I don't. My friend has the same motherboard I do but he is working most of the time. If I have a chance to I will test out my CPU in his motherboard.

Thanks for all the help.
 
Back
Top