Chaintech VNF3-250 HS/F Problem???

Please ne help would be nice im about to order this board tommorrow
 
the zalman fits. i have it installed on the current project i am working on. heres a pic

cleanwires1.jpg
 
are you temps all screwed up, mine are and I want to know if my problem is only on my board
 
Wow thanx for the pic i guess it does fit. Thanks for ur help. BTW how do u like the Chaintech with the Zalmans and wut kind of CPU u got? If u have and benchings on it or anything u would like to share about it good or bad would be greatly appreciatied.
 
im using a 3000+ but i dont know if u noticed there isnt any hard drives installed :(
 
I will be getting a VNF-250 with a Coolermaster Hyper6...in fact it's arriving pretty soon, so I hope it works!
 
Kewl u got the 3000+? also. if so, when u get it together and all tell me wut u like and wut u dont like about it (mobo). Thanx
 
I got the 3200+ :)
Will do, once the system's up. Might take a while though since I haven't even ordered my video card yet(final missing component). I'm still waiting for a good price for a 6800GT that's not out of stock :(
 
Well, the system's up, sans the 6800GT that should be arriving tomorrow. I'm running it on an old GF2MX right now just to setup the system.

A few comments on the motherboard:
1) It's pretty small, smaller than most full size ATX motherboards.
2) The Coolermaster Hyper6 fits nicely, so no worries.
3) Documentation is very very poor. The instruction manual is of average thickness, but is split into many languages, so that each section is only briefly mentioned and not even explained. Other than the pictures showing where the connectors/jumpers are, it's pretty much worthless
4) SATA HDD setup is very unintuitive. It took me hours of trial and error and research to find out that you have to enable both SATA RAID, set primary boot drive to SCSI, and enable "stripe" for a SATA HDD to even be detected. These operations have totally nothing to do with SATA, so I am extremely perplexed as to why Chaintech would arrange their BIOS that way.

That's all for now.
 
I'd agree with most of those statements, but it shouldn't be necessary to go through what you did for a SATA HDD to be detected. The drive, however, will not show up during the boot process or anywhere in the BIOS. You should be able to setup Windows on the drive without any configuration of the boot order or RAID. The newer revisions do show what is detected on the SATA channels both in the BIOS and startup.

Setting up a SATA drive with another IDE drive was a different story. The only way I could boot from the SATA drive was to "hot swap" the IDE drive as Windows began to load, otherwise it would try to boot from the IDE drive. IIRC, the later revisions clear this up as well as the boot order settings.

Overall, a good board for the price, but Chaintech still needs improvement in the BIOS.
 
Well, I have 2 other IDE HDDs other than the SATA drive, and the first time when I tried to install Windows with the other 2 drives connected, BIOS would not see it, but Windows setup saw it. Upon completion of installation though, the SATA drive was detected as F:, with the IDE drive as the boot drive. Obviously I had to reinstall Windows again at that point. My point is, it shouldn't be so hard for SATA/IDE to co-exist. SATA has been around for a while now, so all the kinks should have been worked out. Chaintech is lacking in this respect IMHO.
 
I agree, I was surprised to see no notification or settings for SATA drives.
 
galapogos: what temps are you getting on this board? I have the same setup and the damned Digi dock reads at 49c idel for the cpu and hits a high of 56c. Seems off a little.

also I have had extreme problems after installing the AMD CPU Driver for cool ' quiet. Every single time I do this the system just starts locking up randomly. It could be the WindowsXP boot screen or while playing a game. But the moment I take it off or re dothe system without installing it runs fine.
 
the xp120 fits on it ..i have one with a +2800 @ 2.43ghz on it ..temps read 50'sc idle tho , and that dont seem right ..have reseated hsf a few times to make sure it was on properly , so I would appear it just reads temps hi
 
are you sing cool n' quiet at all?

not saying it;s good but I am atleast glad to see someone else running higher temps lol. I will bust out the compu nurse and seewhat I can tell :D

also for those who dont know how to get cool n' quiet working you have to install the cpu driver form amd and then select minimal power management form the powe schemes are in windows. At tthat point your cpu will idel down when not being fully use. Sadly though on this board Icant use it as it locks me up every time! Other boards were not a problem. Since this is being used in a HTPC the cool n quiet feature is nice to have during idle times or TV viewing.
 
I'm getting way high temps that need to be corrected 10-15C to be sane. This is a known problem with the 07/29 BIOS and CG Newcastles AFAIK.
 
Back
Top