Candle-powered LED Demonstrated

Terry Olaes

I Used to be the [H] News Guy
2FA
Joined
Nov 27, 2006
Messages
4,646
Yeah, it does sound a bit backwards but there’s a point. What these researchers were showing off was the principle of “thermoelectric conversion,” which takes heat and converts it to electricity. This technology has made some strides recently and looks to be commercialized in the near future.

These technologies are all an effort to efficiently convert waste heat, which has been a nuisance thus far, into electricity. Potential heat sources include boilers, hot water pipes, automotive emissions and engines, ICs, microprocessors, transmitters in high-speed telecommunication devices, the sun and human bodies (body warmth).
 
those things are terribly inefficient... doesnt anyone remember these things as a fad for heatsinks on cpu years ago?
 
If they can make it efficient and cheap enough imagine this in your clothes dryer or water heater. But if it's going to cost $10,000 to save $100/year then what's the point.

BTW, the link in the article is dead.
 
Lots of things are horribly inefficient, and lots of things vastly improve in efficency over time.

There are plenty of situations where heat is plentiful, maybe not in powering laptops, but in large-scale power generation there are plenty of places you can dig down a few hundred meters and find an ever-lasting supply of free heat. If they can refine the devices to the extent of economic viability they would represent an everlasting energy source.
 
so what if these devices aren't very efficient at the moment? the fact of the matter is that you can recover some of the energy lost through heat. If I had the money I'd definitely invest in this type of technology.
 
so what if these devices aren't very efficient at the moment? the fact of the matter is that you can recover some of the energy lost through heat. If I had the money I'd definitely invest in this type of technology.

There are car companies working on a device that takes wasted coolant and/or exhaust heat and returns it to the crankshaft via electric motor and a belt.

The power saved (or added to the engines output) is reported to well worth the effort and is in the process of being further refined last I recall.
 
A peltier is merely a polarized stack of P type and N type silicon, They can possibly be extremely cheap to make and can possibly be made thin and flexible. If they can become cheap to a point to where they can be integrated so be it. Its also a demonstration of such a technique exists, just that it has yet been exploited. Peltiers have had very little R&D into them and the present a most interesting property.
 
but its not a new technology. its very old. any improvements to efficiency will have to come in the form of a major breakthrough- much like needs to happen with batteries before they become realistically viable to power cars,
 
No need to convert wasted heat to electricity, I could use all the waste heat right now to warm up. Damn climate change (changed from fall to winter) has us folks up north feeling a wee bit chilly.
 
we had over a foot of snow on the ground for xmas, then for two days it was 50 degrees and melted most all of it, then dropped 30 deg in about 4 hours and we now have this nice 2 inches of solid ice on the ground
 
i dont get why they dont just make small nuclear power to power stuff.
 
They thought about it for cars and such.

I think there would be a problem with small nuclear powered devices, if say a car engine blows up and takes out a city...
 
Using human body heat to power things? Isn't that what happens in the Matrix?
 
Using human body heat to power things? Isn't that what happens in the Matrix?

The human body generates more bio-electricity than a 120-volt battery and over 25,000 BTU's of body heat. Combined with a form of fusion the machines have found all the energy they would ever need.
 
Did anyone notice that the upper portion of the platform the LED was resting on looked like an old style P4 heatsink (sans extended CPU contact area)?
 
Did anyone notice that the upper portion of the platform the LED was resting on looked like an old style P4 heatsink (sans extended CPU contact area)?

it probably is. back in the 90's there was a fad to use peltiers for super-cooling cpu's. you can get you cpu to run overclocked like hell, stable at less then room temp or even freezing... but the catch was you had to run more power then the entire pc normally used.
 
Back
Top