Boot / System Problem PLEASE HELP!

Kaishu

n00b
Joined
Apr 26, 2005
Messages
3
Hi,

Right, here goes.

Ive recently been having some serious problems with my PC
I have an ASUS A7N8E-E Delux motherboard with an AMD Barton 2800 and 1gig of RAM

This has [until this problem arose] been overclocked to 3200 with no problems. I have 2 friends with identical setups and neither have the same problem as me.

The system had been running fine for about 4 months until last week when I turned it on and nothing appeared from the monitor.
I turned it off and tried again. The computer had trouble getting past the post screen. I tried resetting the BIOS so that the PC was running at its default speed. the PC then booted fine so I went back into the BIOS and overclocked it as before. Again it booted fine.

However, I noticed that after playign games of watching videos for a while the system became very slow. The CPU was running at 60-70 percent when idle.

So this is the current situation. I have reset the BIOS again and this is the sequence of events that occurs when I try to boot the PC:

1) PC starts, nothing displayed on monitor [as before]
2) on 2nd boot attempt, computer takes a long time to detect IDE drives and then goes into the Nvidia Boot Agent:

NVIDIA Boot Agent 201.0440
Copyright C 2001-2004 NVIDIA CORPORATION
Copyright C 1997-2000 Intel CORPORATION

CLIENT MAC ADDRESS: [numbers and letters]

which then goes to:
PXE-EGI:Media test failure.check cable
PXE-M0F:Exiting NVIDIA Boot Agent
Disk boot failure please enter system disk

3)I then reboot again and it *usually* boots to windows.

I've read lots of other forums saying to check the cables etc... but surely its not the cable if the PC boots up on the third attempt

Any ideas?

Is it possible that my CPU / RAM / MOBO / Hard Drive is broke?
The thing that confuses me the most is how this problem happened on its own overnight and how the computer manages to boot on the third attempt

Any and all help will be greatly appreciated
 
First, I would say check the ASUS site and see if there is a known issue with that board and BIOS version. Next step should always be a minimal boot. Disconenct all drives and devices from the MB. See if it POSTs fine. If not, you've narrowed it down to MB, CPU and RAM. Next, if you have more than 1 stick of RAM, boot with only one and swap to see if you can recreate the problem. Next, swap your CPU with one of your friends. See if it does the same thing. If none of these solve the problem, then it looks like the MB is the culprit.
 
Thanks for the reply.

I took a quick look on the Asus website.. not very helpful.
Guess I'll have to start swapping out components with my friend until I find the culprit!
 
check ram slots......

remember for dual channel the 2 dimms have to be in the SAME COLOR slots.....

i had similar problems wen i bought my Athlon 64 system....cuz i put the dimms in slots 1 and 3....which happened to be the right configuration for dual channel on my OLD abit motherboard,,,,and i found out that for this one it is different....the same color dimms are 1 and 2 for dual channel.....i put my ram stick there and it worked fine


oops. i just read that your CPU is a Barton...dont know if they're dual channel....

anyway try wat i said
 
arman01 said:
check ram slots......

remember for dual channel the 2 dimms have to be in the SAME COLOR slots.....

i had similar problems wen i bought my Athlon 64 system....cuz i put the dimms in slots 1 and 3....which happened to be the right configuration for dual channel on my OLD abit motherboard,,,,and i found out that for this one it is different....the same color dimms are 1 and 2 for dual channel.....i put my ram stick there and it worked fine


oops. i just read that your CPU is a Barton...dont know if they're dual channel....

anyway try wat i said

Yes, that mobo is an NForce2 board that supports dual channel memory. I would re-seat the ram, and all lcards (especially vid card).

I have seen some IDE cables go bad in the past (I have NO IDEA why, but there ya go) so I would re-seat them, and even replace the primary IDE cable to the boot drive.

You are about to enter hardware hell... good luck!

-Skystalker
 
Back
Top