Best IC7-MAX3 OTES-compatible heatsink?

mikeblas

[H]ard|DCer of the Month - May 2006
Joined
Jun 26, 2004
Messages
12,777
I'm running a 3.2 GHz Prescott on my IC7-MAX3, and I'm tired of the high temperatures.

Right now, I've got the OEM heatsink and ABIT EQ is reporting temperatures around 74 degrees celcius under load. Even figuring this board reports 13 degrees high, I'm still uncomfortable with a temperature of 61 degrees.

What's the best heatsink can fit on the MAX3 motherboard with that OTES cooling tunnel?

I've seen some posts that say the Thermalright SP-94 is good. It looks like a monster; does it really fit?

.B ekiM
 
NuclearFallout said:
An xp-120 their new heatsink will fit too.

Is that thing shipping yet? Any ETA?

What about the SLK-800U? I think it might be quieter.

.B ekiM
 
mikeblas said:
Is that thing shipping yet? Any ETA?

What about the SLK-800U? I think it might be quieter.

.B ekiM
Just FYI, an XP-120 with a good 120mm will probably be less annoying because the tone of a 120mm is much more of a hum, rather than a whine, like some of the smaller fans.

And yes, it is shipping. check www.svc.com, I believe they have them instock.
 
Rizen said:
Just FYI, an XP-120 with a good 120mm will probably be less annoying because the tone of a 120mm is much more of a hum, rather than a whine, like some of the smaller fans.

Thanks for the link, Rizen.

Do you think the XP-120 would fit over the OTES? It's giant! I'm not even sure it will fit my case.

.B ekiM
 
mikeblas said:
Thanks for the link, Rizen.

Do you think the XP-120 would fit over the OTES? It's giant! I'm not even sure it will fit my case.

.B ekiM
To be honest, i'd just get rid of the OTES all together. The 40mm fan is WHINY. If you're worried about noise at all (and/or if you are TRULY picky) the 40mm is the first thing to go. The sinks aren't even TIMed.. They're just being pushed down onto the MOSFET by some cheesy springs. If you add a few of your own sinks (or just thermal epoxy them back onto the MOSFETs) then the spillover from a 120mm fan would EASILY cool them BETTER than the OTES system ever could. Another thing to consider is that those heatsinks are all facing perpendicular to the fan/airflow, so they're not as efficient as they could be.

I took mine off and am not seeing any performance degredation. Just my 2 cents.
 
mikeblas said:
Thanks for the link, Rizen.

Do you think the XP-120 would fit over the OTES? It's giant! I'm not even sure it will fit my case.

.B ekiM
I don't know if it will fit OTES because frankly I am not sure what OTES actually is, haha. But if you have any questions regarding fit, maybe give SVC a call, or read one of the reviews that have been posted. Those should have some fitment pictures - maybe someone used a similar setup?
 
Rizen said:
I don't know if it will fit OTES because frankly I am not sure what OTES actually is, haha.

You can read about OTES at the ABIT-usa website.

Rizen said:
Those should have some fitment pictures - maybe someone used a similar setup?

I haven't found a review that invovlves the MAX3 motherboard. I'm asking here to find other folks who have installed aftermarket heatsinks on this motherboard.

.B ekiM
 
mikeblas said:
You can read about OTES at the ABIT-usa website.



I haven't found a review that invovlves the MAX3 motherboard. I'm asking here to find other folks who have installed aftermarket heatsinks on this motherboard.

.B ekiM
Are they using your board here?

http://www.systemcooling.com/thermalright_xp120-02.html

"The image above shows the completed installation on our Abit IC7 test board. For performance testing, we utilized a low speed Papst fan, which moves 55 cfm of air at a sedate 1900 rpm, and we further hobbled it by turning the fan voltage down to approximately 10 volts, which results in almost dead silence, and a fan speed of around 1500 rpm. As is made quite clear in the image, you definitely won't be using a tall Northbridge cooler in conjunction with the XP-120. Aside from that caveat, along with the proximity of the fan clips to the rear exhaust fans, there was really no interference anywhere, although it remains to be seen how the unit will fit on other P4 boards."
 
thermalright said it will fit a max 3. If you got any special northbridge cooler like swiftech's one it prolly wont fit though
 
Back
Top