Best BIOS for IC7 overclocking???

publik_en3my

Weaksauce
Joined
Apr 17, 2004
Messages
98
Dear bros,

I am using the ABIT IC7 mobo. Can you'all suggest me which BIOS is best for overclocking?

I have: 2.4C, 512MB Corsair TwinX 2-3-2-6 and Raddy 9800 Pro.

Btw, does the SerialATA drive affect the overclockability of the system?

I am looking forward to yer answers. Thanks
 
ive used a bunch of different ones, all the same for me. but im held back by my proc not my board. so.... there u go
 
It is always better to get latest bios. Bios 24 in particular. Each bios has its fixes. I am using right now bios 24 since yesterday. Seems to be very stable at stock speed.
 
I am using an BIOS 24 too. However, my RAM can not go any further 220MHz (2325) with VDDR default.

This morning, I tried to push CPU FSB to 266 to run 5:4 with my RAM. As the results, I need to clear my CMOS :D.
 
publik_en3my said:
I am using an BIOS 24 too. However, my RAM can not go any further 220MHz (2325) with VDDR default.

This morning, I tried to push CPU FSB to 266 to run 5:4 with my RAM. As the results, I need to clear my CMOS :D.

try holding down the insert key as you poweron the system, that will load the system with default values temporarily.
 
holding down insert will clear CMOS? I thought you always had to change the mobo jumper to "clear CMOS" and do it that way....
 
stumpy said:
holding down insert will clear CMOS? I thought you always had to change the mobo jumper to "clear CMOS" and do it that way....

it doesnt clear the cmos, it will boot using the default values so you can go into the bios and correct whatever made your computer unbootable. its an old feature thats been around since the 440bx boards.
 
acascianelli said:
try holding down the insert key as you poweron the system, that will load the system with default values temporarily.

Thanks for your suggestion. I think I do not need to set the clear CMOS jumper any longer. ;)
 
acascianelli said:
it doesnt clear the cmos, it will boot using the default values so you can go into the bios and correct whatever made your computer unbootable. its an old feature thats been around since the 440bx boards.

Sweet, will this work on the IC7-G too?
 
stumpy said:
holding down insert will clear CMOS? I thought you always had to change the mobo jumper to "clear CMOS" and do it that way....

Hey, I tried to do as ya said last night. It did not work man. I gotta clear da CMOS again :)

BTW, my mutha f*ck'n CPU can not go any higher than 260 although VCore was said to 1.575V. Jesus, think I need to push the Vcore further for a higher clock. I've set the ratio is 5:4
 
You should feel blessed that your motherboard will even post at a front side bus setting of 260. I have a 2.4c and an IC-7 as well, and I could only achieve a high of 250 with a 5:4 ratio before it wouldn't post anymore. I don't think that you can complain too much at all.

Dark Assassin
 
I have had every bios since the ic7-g came out a year ago and ive always hit the same wall at 297 mhz fsb (never prime stable). I dont think you'll have any problems reaching your chips max oc on any of the BIOSs, so just use the newest one.

SATA will not effect the overclockability of your system, just make sure you have the agp/pci lock on.
 
Back
Top