Bad Motherboard?

blade52x

2[H]4U
2FA
Joined
Sep 9, 2006
Messages
3,235
I recently ordered an i3-540 and ASRock H55M-LE off of NE. Right from the beginning, things just weren't working right. Initially the computer just wouldn't boot with both sticks of RAM installed. So I thought it was bad memory, but after using multiple sets, and testing each one, one at a time, it turns out that something is off with memory slot 1. But finally at some point, it booted with both, and seemed to boot up every single time after. So I left it alone.

Then I began overclocking... and noticed some strange behavior. Prime and OCCT were giving me stability all the way up to 4.4ghz, but there just these random hangups and reboots - even during idle. So I figured my overclock was unstable. I backed it down to stock, as I had to move a bunch of stuff of of the 250gb drive onto an external. When I plugged in the external (via USB) and began copying, about 10% of the way in, the system froze and rebooted. What the fucking hell! And now the external doesn't even show up under my hard disk drives when plugged in (even though it's detected and showing up in Disk Management, I cannot do anything with it).

I also remember at some point getting upset, and lightly hitting the case, which caused some kind of weird freeze where it looked like a VRAM failure (colored blocks everywhere) - except I'm using the IGP on the i3?

Cold booting overall is a hit or miss. Sometimes it'll cycle on and off 3 times before it boots. Sometimes it will boot on the first try. If it was a bug, it should be a consistent issue? The cold booting is not consistent at all.

I've requested an advance RMA from NE, but damn... I've wasted too much time here. I was having fun with this i3 too. :(
 
Given what you've described, I'd be looking at the motherboard too. I would also check the voltages reported in your bios, if you haven't already. Could also be a wonky PSU or loose power connection if you smacked the case and it went haywire.
 
Keep in mind you should generlly not run applications like Prime 95 or OCCT on budget boards i can not speak to that ASRock board specifically but my expecatation is the VRM is desgined for generally basic stock operation with possibly very limit overclocking ( 4.0GHz and below ). If pushed too much the VRM assembly ( mosfet or driver could have reached a failure point especially if they do not have good OCP and OVP settings for the board ). This could yield the issue you are noting. I would go back down to defaults and see if the board responds normally at all.

Hope it helps.
 
I think I either had a loose power connection, or some kind of short or ground issue inside of the case the first time around. When I took everything out and hooked up the bare minimums (just the SSD really), everything seemed to work fine. Then I put everything back into the case and hooked up the second hard drive, dvd, fans and etc, and everything still worked. I think I'll have to cancel the RMA.

It's stable at 4.2ghz with something like 1.34v under load. Around 4.4 the voltage starts to increase dramatically (wasn't occt stable for longer than 5 minutes at 1.41v load). But, there are bunch of options I am unfamiliar with in the bios that may need adjusting for that much of an overclock. I am not anywhere near temperature limited with the H60 right now. Either way, I'm happy that I was able to break 4ghz on this chip pretty easily. It was definitely worth it over a locked i3 sandy imo. Too bad there are no 2120k chips. But even if those do get released, I'm sure they will carry a huge price premium over the $90 i3-540.

And as far as overclocking on a budget board to reply to the post above, the issue previous was present whether overclocked or not. It seems gone now. Sure budget boards aren't going to clock as high as those built specifically for overclocking, but if ASRock didn't want anyone overclocking on their budget H55, they would have locked down bios imo. It's also a dual core and not a quad, so the VRMs aren't really being stressed as much as if I was overclocking, say an i7-920. I remember back when I had an IP-35E, the difference in system temperatures when loading an E6600 vs a Q6600 was huge. It handled a heavily clocked E6600 fine, but a heavily clocked Q6600 was causing parts of the board to go above thermal spec.
 
Last edited:
Yeah those 1st gen i3's are a blast, building a little gaming rig for nephews right now with i3 530/Asus P7H55, got it at 4.2GHz and temps on a Hyper 212+ are around 60c full load.
I haven't pushed for more as I think that should suffice, 4870 1Gb with aftermarket TR cooler, should play some games for a while, they're like 11 and 13
 
Um, does that board have a 4 pin CPU power connector, or an 8 pin?
You're not going to have much success pushing the vcore with a 4 pin power connector, with barebones VRM config. Some boards limit the vcore on those budget systems to 1.35'ish.

That CPU would probably run a lot better, and require less voltage, on a higher board.
At least you got it working stable, though, but don't push the vcore so high without an 8 pin connector.
 
Maybe, maybe not. But, I didn't want to spend a lot. I really wanted to see just how far I could push budget. The H60 is overkill, but at least it's silent. :p

To answer your question - 4pin. In techPowerUp's review of the i3, they noted exponential voltage requirement above 4.2ghz. On mine, I can get 4.3 with a little bit more than I run it at right now, and 4.4 is where the voltage really starts to take off. I don't think a higher end board would make a major difference here, but maybe one day I'll look into the FS/FT and see what is available. But for a board and chip for $150 combined, it's amazing.
 
Back
Top